'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EKOPIPE 900 Blue’. Factory applied, blue coloured, two-component epoxy coating. Mix parts A & B in a mass ratio of 2:1 and apply as per manufacturer's TDS 'No:09, Rev.Date: January 2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SikaTop® 550 Seal’. Site applied, white coloured, two component Acrylic, Cementitious waterproofing coating. Mix 1kg of part A (powder) with 333g of part B (liquid) and apply as per manufacturer’s method statement ‘10/2024’. Cure for 28 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polymer Admixture 850'. Site applied, white coloured liquid primer/sealer. Mix 'Polymer Admixture 850' & water in a volume ratio of 1:1 and apply as per manufacturer’s Product Data Sheet dated Jan 2023. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
‘Georg Fischer (+GF+) HDPE PE100 Pipes and ‘Hepworth MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'Polyfab PE100 Pipe' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 85°C.
'Polyfab PE100 Fittings' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured, injection moulded PE100 fittings. For use with water up to 85°C.
‘+GF+ HDPE PE100 Pipes' and '+GF+ MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'CR-01 PE Pipe'. Blue coloured, extruded PE pipe. For use with water up to 23°C.
'Kasta® HDPE PE 100 Pipe (Black)'. Black coloured (with blue external stripes), extruded HDPE pipe. For use with water up to 65°C.
'Revolve N-461 Natural'. White coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Revolve N-250 Light Grey M2-5321'. Grey coloured PE material manufactured by rotomoulding. For use with water up to 85°C.
'Borealis HE125MO & Bn HE125MO-100'. White coloured (semi-opaque), injection moulded PP-H materials. For use with water up to 85°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterCrete ANC 920'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1', dated '09.12.2024' Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterCrete ANC 915’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 1', dated '09.12.2024'. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VULKODURIT 1250 KTW'. Dark grey/brown coloured, Ebonite rubber material made by extrusion and calendaring. Shore hardness 72D. Tested in-radius size 2.0mm. For use with water up to 40°C.
'E7331'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
'E8124'. Black coloured, injection moulded EPDM seal. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
'E50B01, E70B01 & E80B01'. Black coloured, compression moulded EPDM material. Shore hardness between 50, 70 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'CERULEAN EP 14 (KIEP14)'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'8550C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP55 & EP70'. Black coloured, compression moulded EPDM materials. Shore hardness 55 & 70. Tested in-radii size 1.0mm. For use with water up to 70°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
'WAGUNIT H 1005'. Light brown coloured, compression moulded natural hard rubber. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'NOVIPRO'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'RIAMAXX HR XE4355 KTW-M schwarz & RIAMAXX HR XE4355 KTW-M sondergrau K 7-140‘. Black or grey coloured, injection moulded PK materials. For use with water up to 60°C.
'Butyl IIR 6038 diaphragm'. Black coloured, injection moulded Butyl diaphragm. Shore hardness 64 ShA. Tested in-radius size 1.25mm. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The E2WXX, E2BXX & E2GXX models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The E1WXX & EW1WXX models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Non-verifiable double check valve assembly with DZR brass body (chrome plated), incorporating two in-line check valve cartridges. Maximum working pressure – 10.0 Bar Maximum operating temperature - 85°C
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates an isolation valve and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet swivel nozzle combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with cross top operating members. The outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste, not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole bidet combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The swivel nozzle outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperatures 85°C (K26PMA-01NP model) and 65°C (K40P-01NPX model).
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies). Incorporating ceramic cartridge headworks and single lever operating members. The flexible spout outlet incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 166 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
