Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Push fit versions only can also be used with both polybutylene pipe (manufactured to BS7291-2) and PEX pipe (manufactured to BS7291-3) Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome DZR brass bodies. Outlet pressure range: 1.0 - 6.0 bar. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass bodies (nickel plated), brass ball, PTFE seats and EPDM ‘O’-rings. For use with Polybutylene pipe (manufactured to BS7291 part 2), PEX pipe (manufactured to BS7291 part 3) and copper pipe (manufactured to EN 1057). Maximum working pressure: 6 bar Maximum operating temperature: 95°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models SCM020000535, SCM025000536, SCI100000533, SCM025002164 & SCM032002165 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of double regulating valves with bronze bodies, DZR brass discs, EPDM `O`-rings and PTFE disc face. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function. The D931, D933 and D934 models incorporate two pressure test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
'ITK-STE 221 (cream coloured), ITK-AL 99 (cream coloured) & ITK-AL96 (white coloured)'. Compression moulded and sintered ceramic sealing rings. For use with water up to 85°C.
'Wudu brand-NF 131118'. Factory applied, black coloured, two-component, water based epoxy coating. Mix in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V2', dated '20240821'. Cure for 1 hour@50°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW– JAL (OPC-TICL)'. Factory applied, grey coloured Ordinary Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (SRPC-DCL)'. Factory applied, grey coloured Sulphate resistant Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (BFSC-JSL)'. Factory applied, grey coloured Blast furnace slag cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20' and apply as per. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIANYI SUNS-011'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'Tianyi Suns-0023', version 'TYS-02', dated '2021-05-04'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
SI-55678 (shore hardness 50), SI-65678 (SH 60), SI-75678 (SH 70) & SI-85678 (SH 80) natural ‘O’ rings. SI-52109 (shore hardness 50), SI-62109 (SH 60), SI-72109(SH 70), SI-82109 (SH80) red coloured ‘O’ rings. SI-51501 (shore hardness 50), SI-61501 (SH 60), SI-71501(SH 70) & SI-81501(SH 80) blue coloured ‘O’ rings. Natural (appears white coloured), red or blue coloured, compression moulded silicone rubber ‘O’ rings. Shore hardness between 50 shore A and 80 shore A. Tested in-radii sizes between 0.5mm & 2.5mm. For use with water up to 85°C.
WC douche set including a trigger spray, flexible hose and wall outlet with stop lever. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Page 164 of 176
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
