Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
Range of UV Disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EKOPIPE 900 Blue’. Factory applied, blue coloured, two-component epoxy coating. Mix parts A & B in a mass ratio of 2:1 and apply as per manufacturer's TDS 'No:09, Rev.Date: January 2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Enviroline 2405'. Site applied, off-white coloured (once mixed and applied), two-component epoxy. Mix parts A (light grey, opaque liquid) and B (white, opaque liquid) in a volume ratio of 2:1 and apply as per manufacturer's TDS 'Ref:10139', 'Issue Date:8/21/2017'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polymer Admixture 850'. Site applied, white coloured liquid primer/sealer. Mix 'Polymer Admixture 850' & water in a volume ratio of 1:1 and apply as per manufacturer’s Product Data Sheet dated Jan 2023. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GUR® 4012, GUR® 4012 ECO-B, GUR® 2105, GUR® 2105 ECO-B, GUR® 2122, GUR® 2122 ECO-B, GUR® 2126, GUR® 2126 ECO-B, GUR® 4017, GUR® 4017 ECO-B GUR® 4018, GUR® 4018 ECO-B, GUR® 4120, GUR® 4120 ECO-B, GUR® 4150, GUR® 4150 ECO-B, GHR® 8020 & GHR® 8020 ECO-B’. Natural (material appears white/cream coloured, opaque) compression moulded UHMW-PE materials. ‘GUR® 2105, 2105 ECO-B, 2122, 2122 ECO-B. 2126, 2126 ECO-B’ are for use with water up to 60°C. ‘GUR® 4017, 4017 ECO-B, 4018, 4018 ECO-B 4012, 4012 ECO-B, 4120, 4120 ECO-B, 4150, 4150 ECO-B, GHR® 8020 & 8020 ECO-B' are for use with water up to 85°C.
'Revolve N-250 Light Grey M2-5321'. Grey coloured PE material manufactured by rotomoulding. For use with water up to 85°C.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Page 161 of 176
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
