'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Penosil PVC Pipe Adhesive 935 & Penosil Adhesivo PVC-U A-35'. Clear (transparent) solvent cements intended to join PVC pipe and fittings. Apply as per manufacturers technical data sheet. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve that is activated via an infrared sensor. Certain models incorporate a mixer spout which incorporates a manual temperature control. The spout outlets also incorporate a plastic flow straighter. Maximum working pressure; 5 Bar Maximum operating temperature: 60°C
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85.0°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals and NBR O-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of balancing valves with DZR brass bodies Maximum operating pressure 25 bar. Maximum operating temperature 99°C
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), models (63792 & 63794) incorporate ceramic cartridge headworks, model (63793 incorporates quarter turn ceramic disc headworks both with single lever operating members. The spout outlet is a pull-out spray type. The inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assembies (stainless steel bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator and some of the products are supplied with click type pop-up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 90⁰C.
Single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever type operating member. The spout outlet incorporates a plastic aerator and flow regulator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Page 147 of 223
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
