'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VYDYNE AG7K-1001'. Light grey coloured, injection moulded PA66 material. For use with water up to 70°C.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'+GF+ Hakan HDPE PE100 Pipes'. Extruded PE100 pipes which are either blue coloured or black coloured (with blue stripes). For use with water up to 23°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'DELAV HDPE Pipe PE100' and 'DELAV HDPE Pipe PE100-RC'. Black coloured (with blue stripes), extruded PE pipes. For use with water up to 23°C.
'STAR Spigot Fittings'. Black coloured, extruded PE100 fitting. For use with water up to 60°C.
'GPS Excel Black PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'Sylglas Plumber Fix Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TELCOR THL FGEB 80G NC'. Black coloured, calendered, natural rubber material. Shore hardness 80D. Tested in-radius size 1.2mm. For use with water up to 23°C.
'EP11/7/4 BLK'. Black coloured, injection moulded EPDM rubber `O` rings & gaskets. Shore hardness 70. The ‘O’-rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 1.4mm. For use with water up to 85°C.
'EPDM B1-4710'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.55mm. For use with water up to 85°C.
'CH EP 172 DM'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SE-808PF'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7037K'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Pango2023'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
'NBR N65WKZ'. Black coloured, injection moulded NBR rubber material. Shore hardness 59. Tested in-radius 1.0mm. For use with water up to 23°C.
'N65WKZ'. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'S7107'. Red coloured, injection moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
Range of push fit stop valves with white plastic bodies. Maximum working pressure/temperature: 10bar @ 20°C and 4 bar @ 60°C.
Floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates manual diverter to a shower outlet. The spout outlet incorporates an open outlet type spout. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure - 8 Bar. Maximum operating temperature - 65 °C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) mains electric or battery controlled tap assemblies (chromium plated brass) incorporating approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection . The flow is controlled via a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The tap is supplied with spherical valves for both hot and cold inlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Sekisui F range of un-insulated GRP sectional cisterns. The larger cisterns have stainless steel internal bracing and UPVC pole supports. Insulated cisterns were added to the approval in March 2025. All cisterns are for cold water use only.
Ceramic cartridge headwork with a plastic body, incorporating a silicone rubber ‘O’ ring. Intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of deck mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model) Maximum working pressure 6 Bar. Maximum operating temperature 65 °C
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with either (chromium plated or matte black finish brass bodies), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Single-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with an approved click-type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with lever operated pop-up wastes. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a click-type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 146 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
