'EPDM 5518 Seal 3G'. Black coloured, compression moulded, EPDM rubber seal. Shore hardness 58. Tested in-radius size 1.92mm. For use with water up to 23°C.
'EW gasket material'. Black coloured, injection moulded, EPDM gasket material. Shore hardness 65A. Tested in-radius size 3.9mm. For use with water up to 65°C.
'E6029 (shore hardness 70) & E6392 (shore hardness 80)'. Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'‘Welding polymer for Kryoclim®️, Girair®️ and HTA (formerly known as GIRPI HTA Fusion THF Free'. Site applied, orange coloured solvent cement, intended to join PVC-C pipe and fittings. Apply as per pages 4.2 & 4.3 of 'Durapipe HTA®' technical data sheet '04900200 February 2013'. Cure for 24 hours at 7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member, a manual diverter to shower outlet and a waterfall type spout. Shower hose and handset is not supplied with this product. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies, (chromium plated brass body). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled, tap assemblies (chromium plated brass). The flow is controlled via solenoid valves, actuated by infra-red sensors. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, electronically operated tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve and actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose connection incorporates a stainless-steel strainer. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) over the rim swivel nozzle bidet combination tap assembly (brass body - various finishes) with a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The products incorporate a pull-out spout with a plastic aerator. Both models incorporate an approved check valve cartridge within the quick connector to the pull-out hose, and the inlet to the pull-out spout of the 63036-01X model incorporates an approved check valve cartridge with a plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 139 of 207
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
