'CER/ISO-CER'. Grey coloured, Sintered Ferrite magnet component. For use with water up to 85°C.
'ULTRAMID® A3EG7 AQUA BLACK 00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'ULTRAMID® B3EG3 AQUA BLACK00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'ForTii Ace WX51-FC NA99001'. Natural (appears beige in colour), injection moulded Polyamide material. For use with water up to 85°C.
'Durethan BKV15F 901510 DUS018'. Black coloured, injection moulded PA6 GF 15 material. For use with water up to 85°C.
'PolySTH Pushfit Fittings'. Injection moulded, polybutylene pushfit fittings available in white and grey colours. For use with water up to 85°C.
'PolySTH pipe'. Grey coloured, extruded multi-layered pipe consisting of a polybutylene inner and outer layer and a dark grey coloured EVOH middle barrier layer. For use with water up to 85°C.
'ROMAPEX (Pipe PE-Xb EVOH 5L)'. Extruded, multi-layered pipe comprising of a white coloured PE-Xb inner layer, black coloured EVOH layer and white coloured PE-Xb outer layer. For use with water up to 85°C.
'SAS HDPE Pipe'. Black coloured (with blue external stripe), extruded HDPE pipes. For use with water up to 85°C.
'Revolve N-307 (5056) Natural'. Natural (appears white), rotationally moulded PE material. For use with water up to 85°C.
'GUR® 4012, GUR® 4012 ECO-B, GUR® 2105, GUR® 2105 ECO-B, GUR® 2122, GUR® 2122 ECO-B, GUR® 2126, GUR® 2126 ECO-B, GUR® 4017, GUR® 4017 ECO-B GUR® 4018, GUR® 4018 ECO-B, GUR® 4120, GUR® 4120 ECO-B, GUR® 4150, GUR® 4150 ECO-B, GHR® 8020 & GHR® 8020 ECO-B’. Natural (material appears white/cream coloured, opaque) compression moulded UHMW-PE materials. ‘GUR® 2105, 2105 ECO-B, 2122, 2122 ECO-B. 2126, 2126 ECO-B’ are for use with water up to 60°C. ‘GUR® 4017, 4017 ECO-B, 4018, 4018 ECO-B 4012, 4012 ECO-B, 4120, 4120 ECO-B, 4150, 4150 ECO-B, GHR® 8020 & 8020 ECO-B' are for use with water up to 85°C.
'Revolve N-461 Natural'. White coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'3802B'. Black coloured, extruded MDPE material. For use with water up to 23°C.
'DIC.PPS Z-230-T5 BLACK'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'LUBRICOMP OFL36A-GYMDNAT'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'ECOSAN ML5 Pipe'. Extruded, multi-layered PP-RCT/PP-R/PP-R pipe which has a grey coloured inner layer and green coloured outer layer. The three intermediate layers are grey in colour. ‘ECOSAN SDR6 Pipe’. Extruded, single layered, green coloured (with red external stripe) PP-R pipe. Both pipes are for use with water up to 85°C.
WATERTEC/CLIMATEC Pipes. Multi-layered PP-RCT/PP-RCT-GF/PP-RCT pipes comprising of a green coloured inner layer, black coloured middle layer and green coloured (with grey stripes) outer layer. For use with water up to 85°C.
'Ultrason® S2010 G4 Schwarz 15038'. Black coloured, injection moulded polysulphone material. For use with water up to 85°C.
'Steckkörper 2675 Fitting'. White coloured (opaque), PVDF component injection moulded from 'amboflon® PVDF 24'. For use with water up to 85°C.
'51M7531 Diaphragm'. Black coloured, calendered, EPDM diaphragm. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 85°C.
'ERA10-2 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'ME0940/40 - 90'. Black coloured, injection moulded EPDM rubber material. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 3.0mm. For use with water up to 85°C.
'OLD ETP890 70N'. Black coloured, injection moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 85°C.
'3E60B11P & 3E70B03P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'SU26F415H01 'O' ring'. Black coloured, compression moulded FKM rubber 'O' ring. Shore hardness 80. Tested in-radius size 0.9mm. For use with water up to 75°C.
'V8 Fluorocarbon Rubber Bellows'. Black coloured, injection moulded fluorocarbon rubber bellows. Shore hardness 70. Tested in-radii sizes between 0.7mm & 4.1mm. For use with water up to 85°C.
'Type 1 O-ring, T056D 124H16 Model Code P16'. Cream coloured (opaque), compression moulded silicone rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Loctite 5800'. Red coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated April 2012. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Penosil PVC Pipe Adhesive 935 & Penosil Adhesivo PVC-U A-35'. Clear (transparent) solvent cements intended to join PVC pipe and fittings. Apply as per manufacturers technical data sheet. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Butyl IIR 6038 diaphragm'. Black coloured, injection moulded Butyl diaphragm. Shore hardness 64 ShA. Tested in-radius size 1.25mm. For use with water up to 85°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Non-Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated DZR brass body. The assembly incorporates an isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with nickel plated or natural finish. Models with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Models 12.10152.015.CP02-8511 & 12.10152.015.CP5R-8511 have a maximum operating temperature of 65°C. All other models have a maximum operating temperature of 85°C
Non-verifiable double check valve assembly with DZR brass body (chrome plated), incorporating two in-line check valve cartridges. Maximum working pressure – 10.0 Bar Maximum operating temperature - 85°C
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates an isolation valve and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle headworks with a brass body and EPDM ‘O’-rings. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85.0°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals and NBR O-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of balancing valves with DZR brass bodies Maximum operating pressure 25 bar. Maximum operating temperature 99°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), models (63792 & 63794) incorporate ceramic cartridge headworks, model (63793 incorporates quarter turn ceramic disc headworks both with single lever operating members. The spout outlet is a pull-out spray type. The inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 122 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
