Range of globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with stainless-steel bodies and EPDM o-rings. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 25.0 Bar. Outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.
Range of latching (LV), proportional (PV), servo (SV), pilot (EV) solenoid valves with natural (appear white), plastic bodies. Valves with black coloured plastic bodies (incorporating a biocide) were added to the approval in January 2026. Pushfit models are for use with John Guest LLDPE and DMFIT LLDPE pipes. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. All valves have a maximum working pressure of 10.0 bar. The bodies of valves with a silicone diaphragm are marked with an ‘S’ at the end of the model, e.g. ‘EV118/AS’ and have a maximum operating temperature 85°C. Valves with an EPDM diaphragm are for cold water use only and do not include this ‘S’ marking.
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spherical valves with DZR brass bodies and incorporating a butterfly operating member. Maximum working pressure: 16.0 bar. Maximum operating pressure: 85 C
Range of spherical valves incorporating a chrome plated brass body & brass ball. Maximum operating pressure 10 bar. Maximum operating temperature 65 °C.
Range of single lever or butterfly handle operated spherical valves with chrome plated brass bodies incorporating chrome plated brass ball. Maximum working pressures: see model below. Maximum operating temperature 23°C.
Range of press fit ball valves with DZR brass bodies incorporating a chrome plated brass ball. To be used with copper pipe EN1057 only. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only.
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models ZHR01B & ZHR01C incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valve with ductile iron bodies, blue epoxy powder coated. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of wall mounted flow control valves with (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks. The product is supplied with various trim sets incorporating a cross top, lever or dome type operating member. Maximum operating pressure 5 bar. Maximum operating temperature 60°C.
Range of manually operated balancing valves with DZR brass bodies. The product also incorporates a spherical valve. Maximum working pressure: 10 bar Maximum working temperature: 100°C.
'POM NW-02 (432U slate grey)'. Dark grey coloured, injection moulded POM material. For use with water up to 65°C.
'ABS757K (9M cool grey) & ABS757K (432U slate grey)'. Light grey or dark grey coloured, injection moulded ABS materials. For use with water up to 65°C.
'M-106'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PUA P'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'Rev - 06/2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PU W'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'Rev -06/2024'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer to be mixed in a 15:4 volume ratio and applied as per manufacturers PDS dated ‘October 2024’. Cure for 16 hours@20°C. 'Hempadur 35560 Cream’ is a two-component coating to be mixed in a 6.8:2 volume ratio and applied as per manufacturers PDS dated ‘May 2024’. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JAZLINE DW'. Factory applied, two-component, light green coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's TDS issued '1 / 2022'. Cure for 7 days@28°C. For use with water up to 60°C.
'P • HSR42.5'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement:medium sand:water in 1:1.4:0.45 weight ratio and apply as per manufacturer's instructions 'Version 03', dated '29th-07-2024'. Cure for 3 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'UW TPE HEA-ISO (manufactured from NAKAN HEA 407 EX)'. White coloured (translucent), extruded TPE hose. Shore hardness 66. Tested in-radius size 0.39mm. For use with water up to 65°C.
'HW Lubrex/009'. Amber coloured (translucent) lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'ULTRAMID® A3EG7 AQUA BLACK 00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'ULTRAMID® B3EG3 AQUA BLACK00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'Durethan BKV15F 901510 DUS018'. Black coloured, injection moulded PA6 GF 15 material. For use with water up to 85°C.
'JXPE100'. Black coloured, extruded HDPE pipe. For use with water up to 65°C.
'Wavin PE-RT Pipe'. Extruded, off-white coloured (opaque) PE-RT pipe. For use with water up to 65°C.
'ELBOR Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 65°C.
'Revolve N-307 (5056) Natural'. Natural (appears white), rotationally moulded PE material. For use with water up to 85°C.
'GUR® 4012, GUR® 4012 ECO-B, GUR® 2105, GUR® 2105 ECO-B, GUR® 2122, GUR® 2122 ECO-B, GUR® 2126, GUR® 2126 ECO-B, GUR® 4017, GUR® 4017 ECO-B GUR® 4018, GUR® 4018 ECO-B, GUR® 4120, GUR® 4120 ECO-B, GUR® 4150, GUR® 4150 ECO-B, GHR® 8020 & GHR® 8020 ECO-B’. Natural (material appears white/cream coloured, opaque) compression moulded UHMW-PE materials. ‘GUR® 2105, 2105 ECO-B, 2122, 2122 ECO-B. 2126, 2126 ECO-B’ are for use with water up to 60°C. ‘GUR® 4017, 4017 ECO-B, 4018, 4018 ECO-B 4012, 4012 ECO-B, 4120, 4120 ECO-B, 4150, 4150 ECO-B, GHR® 8020 & 8020 ECO-B' are for use with water up to 85°C.
'LUBRICOMP OFL36A-GYMDNAT'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'ECOSAN ML5 Pipe'. Extruded, multi-layered PP-RCT/PP-R/PP-R pipe which has a grey coloured inner layer and green coloured outer layer. The three intermediate layers are grey in colour. ‘ECOSAN SDR6 Pipe’. Extruded, single layered, green coloured (with red external stripe) PP-R pipe. Both pipes are for use with water up to 85°C.
'Wavin PP-R Glass Fibre Lined Pipe'. Extruded pipe comprising of a grey coloured PP-R inner layer, black coloured glass fibre middle layer and grey coloured PP-R outer layer. For use with water up to 65°C.
'Poliext PP Compression Fittings PN16'. Black coloured, injection moulded, PP compression fittings. For use with water up to 23°C.
'3950, 3952 & 3955'. White coloured PTFE tapes manufactured by press strip roller. For use with water up to 60°C.
'HEPWORTH uPVC Pressure Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 60°C.
'Steckkörper 2675 Fitting'. White coloured (opaque), PVDF component injection moulded from 'amboflon® PVDF 24'. For use with water up to 85°C.
'TIMO® 3NC-60 'O' rings and Gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 60. Tested in-radius size between 0.5mm & 2.67mm. For use with water up to 85°C.
'EP60/1 BLK 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 1.77mm. For use with water up to 85°C.
'560AL Water Seal'. Black coloured, injection moulded EPDM seal. Shore hardness 70. Tested in-radius size 2.12mm. For use with water up to 23°C.
Page 118 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
