Directory Search Results

Print List

#2112354

Range of gas fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The cold inlet incorporates an angled spherical valve with a brass body, chromium plated brass ball and a lever operating member. The primary circuit incorporates an expansion vessel, isolation valves on flow and return, drain valve and a pressure relief valve set at 3.0 bar. Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature for the secondary circuit is 55˚C. Cold supply only.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2112354
Size:
Secondary: 15mm copper tail. Primary: 22mm copper tail.
Marking:
Biasi and Biasi logo on front panel. Biasi, Biasi logo, pressure, model and other technical information on label on inside cover.
Installation Requirements:
R001 R140 R360
Expiry date:
31/12/2026
Model:
Advance Plus 25C ERP, Advance Plus 30C ERP, Advance Plus 35C ERP, M300V.2025 SM, M300V.2530 SM, M300V.3035 SM, M275V.2024 SM, M275V.2428 SM, M275V.2832 SM.

Approval Holder:
BSG Caldaie a gas S.p.A.
Company Name
BSG Caldaie a gas S.p.A.
Address
Via Pravolton 1/b Pordenone
Postcode
33170
Country
Italy
Phone
+39 0434 238311
General Email
luca_norio@bsgspa.it

View All Listings by this Company

Print This Approval


#2111364

Greenstar Heatslave II range of floor standing oil-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, which incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The cold water inlet incorporates a screwdriver operated spherical valve followed by a plastic flow regulator inserted within the pipework. Maximum working pressure: Primary circuit 2.5 bar. Secondary circuit 10.0 bar. Maximum operating temperature 82°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2111364
Note:
Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999. R430 applies to the EXT models only.
Size:
Primary: 28mm copper tail (25/32 models), 22mm copper tail (all other models). Secondary: 15mm inlet x 22mm copper tail outlet.
Marking:
Worcester (brand of Bosch Thermotechnology Ltd) and Worcester logo on front casing. Data label, Worcester and technical information on inside cover.
Installation Requirements:
R001 R140 R360 R430
Expiry date:
30/11/2026
Model:
7 731 600 165 Greenstar Heatslave II 12/18 ErP+, 7 731 600 166 Greenstar Heatslave II 18/25 ErP+, 7 731 600 167 Greenstar Heatslave II 25/32 ErP+, 7 731 600 168 Greenstar Heatslave II EXT 12/18 ErP+, 7 731 600 169 Greenstar Heatslave II EXT 18/25 ErP+, 7 731 600 170 Greenstar Heatslave II EXT 25/32 ErP+, 7 731 600 260 Greenstar Heatslave II 12/18 2022+, 7 731 600 261 Greenstar Heatslave II 18/25 2022+, 7 731 600 262 Greenstar Heatslave II 25/32 2022+, 7 731 600 263 Greenstar Heatslave II EXT 12/18 2022+, 7 731 600 264 Greenstar Heatslave II EXT 18/25 2022+, 7 731 600 265 Greenstar Heatslave II EXT 25/32 2022+.

Approval Holder:
Worcester Bosch
Company Name
Worcester Bosch
Address
Cotswold Way Warndon Worcester
Postcode
WR4 9SW
Country
United Kingdom
Phone
+44 1905 752761
General Email
ian.sharp@uk.bosch.com

View All Listings by this Company
Manufacturer:
Bosch Thermotechnology Ltd.
Company Name
Bosch Thermotechnology Ltd.
Address
Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire
Postcode
S45 9BY
General Email

View All Listings by this Company

Print This Approval


#2110331

Range of air cooled ice making machines . Inlet is controlled via solenoid valve. Maximum working pressure 5.5 bar. Cold water use only.

Section:
1500 Ice Making Machine(s)
Size:
See model.
Marking:
Manitowoc logo on door. Manitowoc, model, serial number & technical information on body.
Installation Requirements:
R001 R009 R160 R171 R511
Expiry date:
31/10/2026
Model:
I(*)T0300A I(*)T0300W I(*)P0320A I(*)T0420A I(*)T0450A I(*)T0450W I(*)T0500A I(*)P0500A I(*)T0620A I(*)T0620W I(*)T0750A I(*)T0750W I(*)T0900A I(*)T0900W I(*)T1200A I(*)T1200W I(*)T1200N IBT1020C I(*)T1500A I(*)T1500W I(*)T1500N I(*)T1900A I(*)T1900N I indicates Indigo family of Ice Machines (*) Indicates D, Y or R. Dependent on ice cube size (T or P) Indicates refrigerant type (T=R410A, P=R290) 4 numerical characters indicate to icemaking capacity per 24hrs Final character indicates cooling option (A=Air, W=Water, N=Remote Condenser, C=Remote Condensing Unit)
Models added July 2024: I(*)P0300A I(*)P0420A I(*)P0620A I(*)P0620W I(*)P0600A I(*)P0600W I(*)P0900A I(*)P0900W I(*)P1200A I(*)P1200W I(*)P1200N I(*)P1500A I(*)P1500W I(*)P1500N I(*)P1900A I(*)P1900N

Approval Holder:
Pentair Commercial Ice LLC
Company Name
Pentair Commercial Ice LLC
Address
5500 Wayzata Blvd. Suite 900 Golden Valley, MN
Postcode
55416
Country
United States
General Email
jeng.yang@pentair.com

View All Listings by this Company
Manufacturer:
Pentair Commercial Ice LLC
Company Name
Pentair Commercial Ice LLC
Address
5500 Wayzata Blvd. Suite 900 Golden Valley, MN
Postcode
55416
Country
United States
General Email
jeng.yang@pentair.com

View All Listings by this Company

Print This Approval


#2201024

Range of in-line water meters with brass bodies and plastic inlet filters. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C (SJ & ELECTO-SJ models) Maximum operating temperature 30°C (AP VARIO and AP RADIO models)

Section:
1505 Water Meters
Size:
DN15 - ¾” BSP (M) inlet and outlet. DN20 - 1” BSP (M) inlet and outlet.
Marking:
Maddalena logo on meter face or sealing ring. CE, year of manufacture (YYYY) and other technical information on meter face. Flow arrow on body.
Installation Requirements:
R001
Expiry date:
31/01/2027
Model:
SJ, SJ PLUS, SJ EVO, ELECTO SJ models (DN15, length of body 110, 115, 120, 130mm / DN20, length of body 115, 130mm). AP VARIO, AP RADIO models (DN15, length of body 80, 110, 130mm / DN20, length of body 130mm).

Approval Holder:
Maddalena SpA
Company Name
Maddalena SpA
Address
via G.B. Maddalena 2/4 Povoletto (Udine)
Postcode
33040
Country
Italy
Phone
+39 0432 634811
General Email
emanuele.ferrari@maddalena.it

View All Listings by this Company
Manufacturer:
Maddalena SpA
Company Name
Maddalena SpA
Address
via G.B. Maddalena 2/4 Povoletto (Udine)
Postcode
33040
Country
Italy
Phone
+39 0432 634811
General Email
emanuele.ferrari@maddalena.it

View All Listings by this Company

Print This Approval


#2201344

Range of water meter manifolds (plastic body). Model WB31520CG incorporates a single check valve cartridge and model WB31520CGDCV two single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 16.0 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
Size:
¾” BSP (F)
Marking:
Talis on base. Flow arrow on manifold box.
Installation Requirements:
R001 R008
Expiry date:
31/01/2027
Model:
Talbot Matrix: WB31520CG WB31520CGDCV

Approval Holder:
Atlantic Plastics Ltd.
Company Name
Atlantic Plastics Ltd.
Address
Coytraherne Close, Brackla, Bridgend
Postcode
CF31 2AX
Country
United Kingdom
Phone
01656672628
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd.
Company Name
Atlantic Plastics Ltd.
Address
Coytraherne Close, Brackla, Bridgend
Postcode
CF31 2AX
Country
United Kingdom
Phone
01656672628
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2112359

Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
1530 Miscellaneous Fittings
Size:
¾” BSP (F) captive nut x ¾” BSP( M) x 3/4” BSP (M)
Marking:
Flomasta (Brand of Kingfisher), PN10, and size on body.
Installation Requirements:
R001
Expiry date:
31/12/2026
Model:
EPH_WAS20_0056

Approval Holder:
Kingfisher International Products Ltd
Company Name
Kingfisher International Products Ltd
Address
1 Paddington Square, London
Postcode
W2 1GG
Phone
07721 260713
General Email
eric.capotummino@kingfisher.com

View All Listings by this Company

Print This Approval


#2201332

Range of pump inverters with plastic bodies, NBR rubber and EPDM rubber seals and ‘O’-rings. The products incorporate an inline resilient trim non-return valve. Maximum working pressure 13.0 bar. Cold water use only.

Section:
1530 Miscellaneous Fittings
Size:
1¼” BSP (M) inlet x 1½” BSP (F) outlet.
Marking:
DAB Water Technology on front casing. Manufacturer name, CE marking, date of manufacture (N.X.YYWW, where N.x = product revision index) and other technical information on adhesive label on side of casing.
Installation Requirements:
R001
Expiry date:
31/01/2027
Model:
Active driver plus M/T 1.0 Active driver plus M/T 2.2 Active driver plus T/T 3 Active driver plus T/T 5.5 Active driver plus M/M 1.1 Active driver plus M/M 1.8/DV Active driver plus M/M 1.5/DV Models are named “Active driver plus x/y z” or “Active driver plus x/y z/DV” Where: x indicates the configuration of the entry line, which can be monophase (“M”) or threephase (“T”), y indicates the configuration of the exit line, which can be monophase (“M”) or threephase (“T”), z indicates the maximum mechanical power of the pump’s motor and “DV” indicates dual voltage models (able to work at 115V or at 230V).

Approval Holder:
DAB PUMPS SPA
Company Name
DAB PUMPS SPA
Address
Via Marco Polo 14 Mestrino (PD)
Postcode
35035
Country
Italy
General Email
certifications@dwtgroup.com

View All Listings by this Company
Manufacturer:
DAB PUMPS SPA
Company Name
DAB PUMPS SPA
Address
Via Marco Polo 14 Mestrino (PD)
Postcode
35035
Country
Italy
General Email
certifications@dwtgroup.com

View All Listings by this Company

Print This Approval


#2201032

Bypass valve assembly with a plastic body and push/pull operating method to switch flows between different outlets. The product incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Cold water use only.

Section:
1530 Miscellaneous Fittings
Size:
¾” BSP (M)
Marking:
Culligan (owners of Harvey Water Softeners), CBP01 and flow arrows on body.
Installation Requirements:
R001 R008
Expiry date:
31/01/2027
Model:
G3920

Approval Holder:
Harvey Water Softeners
Company Name
Harvey Water Softeners
Address
Hipley Street Old Woking Surrey
Postcode
GU22 9LQ
Country
United Kingdom
Phone
01483 753430
General Email
papillon.bleeker@harvey.co.uk

View All Listings by this Company

Print This Approval


#2112012

Union ball, non-return valve with a plastic PVC body. Maximum working pressure 10.0 bar. Cold water use only.

Section:
1530 Miscellaneous Fittings
WRAS Approval Number:
2112012
Note:
Does not provide sufficient protection against backflow to meet the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. For this purpose reference should not be made to `Backflow Prevention Devices`.
Size:
20mm (F) solvent cement connection
Marking:
Company logo (ERA), PN and size on body
Installation Requirements:
R001
Expiry date:
31/12/2026
Model:
UBC02 20mm

Approval Holder:
ERA Piping (Zhejiang) Co.,Ltd.
Company Name
ERA Piping (Zhejiang) Co.,Ltd.
Address
No.1118 Huangjiao Road, Huangyan Economic Development Zone, Taizhou, Zhejiang
Country
China

View All Listings by this Company
Manufacturer:
ERA Piping (Zhejiang) Co.,Ltd.
Company Name
ERA Piping (Zhejiang) Co.,Ltd.
Address
No.1118 Huangjiao Road, Huangyan Economic Development Zone, Taizhou, Zhejiang
Country
China

View All Listings by this Company

Print This Approval


#2112045

‘ECOCIRC XL N’ & ‘ECOCIRC XL PLUS N’ range of circulation pumps with stainless steel bodies, plastic impellers, and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2112045
Size:
1½”-2” BSP (M). DN32-65 flanged.
Marking:
Lowara (brand of Xylem) and Lowara logo, manufacturer name (xylem brand) and technical information on adhesive label on top of pump.
Installation Requirements:
R001
Expiry date:
31/12/2026
Model:
ECOCIRC-XL N X1-X2 X3 X4 & ECOCIRC-XL PLUS N X1-X2 X3 X4. Where: ECOCIRC XL = series name. PLUS = with communication capabilities. N = stainless steel. X1 = port nominal diameter in mm (25 or 32 threaded models, where 25 = 1½” BSP (M), 32 = 2” BSP (M), 32-65 on flanged models). X2 = maximum head in m x 10. X3 = maximum flow - low flow versions - ‘empty’ = standard version. X4 = flange type - F = flanged, ‘empty’ = threaded BSP (M). Examples: ECOCIRC-XL N 25-40 & ECOCIRC XL PLUS N 65-120F.

Approval Holder:
Xylem Service Italia S.r.l
Company Name
Xylem Service Italia S.r.l
Address
Via Vittorio Lombardi 14, 36075 Montecchio Maggiore-Alte Ceccato VI, Vicenza
Country
Italy
Phone
0039 0444 707111

View All Listings by this Company
Manufacturer:
Xylem Service Hungary Kft.
Company Name
Xylem Service Hungary Kft.
Address
Külso-Kátai út. 41 HU-2700 Cegléd
Phone
+36-53-510502

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 118 of 1043

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.