Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. SP models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. HP models: maximum supply pressure 25.0 bar, outlet pressure range 3.0 to 12.0 bar. LP models: maximum supply pressure 8.0 bar, outlet pressure range 0.5 to 3.0 bar. Maximum operating temperature 60°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of pressure relief valves with DZR brass bodies incorporating EPDM diaphragms. The valves are pre-set as follows: 311560, 312469, 312461ITH, 311461CTS,531661 CST models: 6.0 bar, 312471 CST model: 7.0 bar, 312020 CST model: 10.0 bar. Maximum operating temperature 99°C.
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Some models incorporate a pressure gauge. Valves are pre-set at 3.0, 4.5, 6.0 & 8.0 Bar (all models available for all relief pressures). Maximum operating temperature 99°C.
Range of latching or non-latching normally closed solenoid valves with brass bodies. Maximum working pressure 10.0 Bar to 15.0 Bar (see models). Maximum operating temperature 90.0°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating either brass (870228 &961665) or nickel plated (961159, 961708, 837973, 845188 & 845187) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chrome plated balls, PTFE seats and FKM O-rings. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (brass or chrome plated brass bodies), incorporating chrome plated brass ball and either a single lever or T type operating member. Maximum working pressure 25.0 or 50.0 Bar (see models) Maximum operating temperature 20.0°C
Range of lever (1307 and 1333 models) or screwdriver operated (all other models) spherical ball valves with brass bodies and a chromium plated brass ball. Max working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electronically controlled spherical valves with a smart water leakage shut off, incorporating a ceramic pressure sensor, stainless steel ball and EPDM O-rings. Maximum working pressure; 16 Bar Maximum operating temperature 85°C
Range of lever or butterfly operated spherical valves with brushed chromium plated brass bodies, chromium plated brass ball and PTFE seat. Maximum working pressure; Art. 1700, 1710, 1722, 1711 & 6523 models: ¼” to ½” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Art. 1720 & 1721 models: ¼” to ½” = 64.0 bar, ¾” to 1” = 50.0 bar. Art. 6523 model: ¼” to ⅜” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Art. 6348, 6354 & 6366 models: ¼” to ⅜” = 64.0 bar. Maximum operating temperature 99°C.
Series of brass valves with EPDM o-ring isolation valves with M profile press crimped connections to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ball valves incorporating bronze bodies with quarter turn single lever operating members, chromium plated brass ball and PTFE seal. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of brass spherical valves, incorporating chrome plated brass balls, butterfly type operating members and a drain off spigot connection that incorporates a rising spindle type headwork. For above ground use only. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of spherical valves with stainless steel bodies, chrome plated brass ball and PTFE seats. Maximum working pressure 68.9Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screwdriver operated spherical valves with brass bodies and balls (chromium plated).
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, brass wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a handwheel operating member. Maximum working pressure 20.0 bar. Maximum working pressure 85⁰C. Non-metallic materials and components comply with BS6920 85⁰C use.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with DZR brass bodies with two test ports, incorporating a non-rising spindle headwork. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
‘ProtectoSAN’ range of electrolytic scale inhibitors with chromium plated copper bodies and brass end connectors. Maximum working pressure 20.0 bar. Cold water use only.
‘Alesta Vanguard Blue Epoxy Powder EE80005001723’. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer’s TDS version '22/01/2015'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', issue '04', rev. '0', dated '22.08.2024'. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ARC SD4i(E)'. Factory applied, grey and blue coloured, two-part epoxy coatings. Mix parts A and B in a weight ratio of 2.5:1 and apply as per manufacturer's Application Instructions 'EN-085034EU', dated '01/2025'. Cure for 72 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ARC 858(E)'. Factory applied, dark grey coloured, two-part epoxy coating. Mix parts A and B in a weight ratio of 4:1 and apply as per manufacturer's Application Instructions 'EN-085013EU', dated '08/2024'. Cure for 54 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'novapress®BASIC'. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
'BONDSTRAND GRE Pipe'. Dark green coloured, GRE pipe manufactured by filament winding. For use with water up to 85°C.
'LLS-Magnet'. Grey coloured, pressed & sintered Strontium Ferrite magnet in the form of a washer. For use with water up to 85°C.
'IMAMAG HF85'. Grey coloured Strontium ferrite magnet manufactured by isotropic sintering. For use with water up to 85°C.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'Veradel AG-330 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'Veradel AG-320 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'Sudarshan HDPE Pipes'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 85°C.
'Sudarshan Fittings'. Black coloured, PE fittings made by injection moulding and CNC. For use with water up to 85°C.
'Hydrothen PE 100 Black Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Hydrothene (blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Fasopex Pipe'. Black coloured, extruded PE-X pipe. For use with water up to 85°C.
'TP13444 Black'. Black coloured, rotomoulded, polyethylene material. For use with water up to 85°C.
'8108658 V0010_K LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
Page 109 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
