In line isolation valve with DZR brass body, DZR brass ball (chrome plated), and an EPDM inlet washer. The product incorporates two approved check valve cartridges, one either side of the spherical valve, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar. BS6920 85°C.
Pairs of angled spherical valves with DZR brass bodies (chrome plated), brass ball (chrome plated), stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'YJ-AL2O3 95%'. White coloured, dry pressed and sintered ceramic disc. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘METOLUX Metoset’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'version 2', dated 29.10.2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Wall mounted, metal, single outlet, fixed combination tap assemblies. Flow is controlled by a solenoid valve activated by via an infra-red sensor and temperature adjusted via a single lever operating member. The Inlets incorporate stainless steel strainers & approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (brass bodies - various finishes). Flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled manually with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate single check valve cartridges, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (either black finish or chromium plated brass bodies). Flow is controlled by a solenoid valve which is actuated via an infra-red sensor. The spout incorporates a stainless-steel strainer on the outlet. The product is supplied with a stainless steel braided PEX lined flexible hose assembly and a combination valve with a DZR brass body consisting of a servicing valve, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a stainless-steel strainer and plastic flow regulator on the outlet. The combination valve has a compression inlet for use with copper pipe (manufactured to BS EN 1057). The tap incorporates a soap dispenser with a separate dispensing nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (either black finish or chromium plated brass bodies). Flow is controlled by a solenoid valve which is actuated via an infra-red sensor. The spout incorporates a stainless-steel strainer on the outlet. The product is supplied with a stainless steel braided PEX lined flexible hose assembly and a combination valve with a DZR brass body consisting of a servicing valve, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a stainless-steel strainer and plastic flow regulator on the outlet. The combination valve has a compression inlet for use with copper pipe (manufactured to BS EN 1057). The tap incorporates a soap dispenser with a separate dispensing nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of spring-loaded resilient trim in-line check valve cartridges with acetal bodies. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of in-line single check valve assemblies consisting of a spring loaded resilient trim check valve cartridge housed within a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Model 12.10322.015.CP5R-8511 has a maximum operating temperature of 65°C. Model 12.10322.022.CP5R-8511 has a maximum operating temperature of 85°C.
In-line non-verifiable single check valve assembly consisting of a single check valve cartridge housed within a DZR brass body. Maximum working pressure 16.0 bar. Cold water use only.
Page 91 of 140
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
