'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Durafide® 1130A1T WF900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WF9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'DIC. PPS FZ-2140 BLACK'. 'DIC.PPS FZ-2140 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'DACTAtherm PP-R Fibreglass Pipe'. Extruded, triple layered pipe comprising of a green coloured polypropylene inner layer, a translucent fibreglass middle layer and a green coloured polypropylene outer layer. For use with water up to 85°C.
'DSA Pipe'. Grey coloured extruded PPR pipe. For use with water up to 70°C.
'DSB Fitting'. Grey coloured, injection moulded PPR fittings. For use with water up to 70°C.
'XSPPR-EAC01'. Grey coloured, extruded polypropylene pipe. For use with water up to 85°C.
`Polyfill PPC GF2007 PD1 yellow`. Yellow coloured, injection moulded polypropylene material. For use with water up to 23°C.
'ISOFIL HK 40 5FH0 WT0580'. White coloured (opaque), injection moulded PP material. For use with water up to 85°C.
'ISOFIL H 40 C2 F NA1'. Grey coloured (opaque), injection moulded polypropylene material. For use with water up to 85°C.
`Mecflon Y4`. Black coloured, compression moulded, carbon filled PTFE seal rings. For use with water up to 85°C.
'Corzan PVC-C Pipe'. Grey coloured, extruded PVC-C Pipe. For use with water up to 23°C.
'Corzan PVC-C fittings & valve bodies'. Grey coloured, injection moulded PVC-C fittings & valve bodies. For use with water up to 23°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JP EB 750'. Black coloured ebonite rubber manufactured by calendaring. Shore hardness 75 D. Tested in-radius size 1.03mm. For use with water up to 23°C.
'EP6008'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.8mm. For use with water up to 85°C.
`EP2/9/10 BLK 'O' rings`. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
`EP11/01/13 BLK 'O' rings & seals`. Black coloured, injection moulded 'O' rings & seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.8mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
'E70N01C 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have an in-radius size of 0.5mm. The gaskets have an in-radius size of 1.0mm. For use with water up to 85°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'OYRTEP7011PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 65°C.
'ZF-73'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'V-2 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'REGM20'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'MV250 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Flomasta 7619J'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
Sonlok 3243 & 3577. Site applied anaerobic adhesives. Apply and cure as per manufacturer's instructions. Sonlok 3243 is blue coloured and is for use with water up to 85°C. Sonlok 3577 is green coloured and is for use with water up to 23°C.
`Pool* Filetplast`. White coloured silicone paste. For use with water up to 85°C.
`Pâte d’étanchéité`. White coloured silicone paste. For use with water up to 85°C.
'Unecol PVC New Age Solvent Cement'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'THERMOLAST K TF5WHA, TF6WHB, TF6WHA, TF7WHB, TF7WHA, TF8WHB & TF8WHA'. Injection moulded, natural (appears off-white translucent) TPE materials with a shore hardness of between 55 and 85. Tested in-radius size 1.0mm. The materials may be coloured using one, or any combination of, the following Kraiburg pigments (up to and including the maximum level included): Black (maximum level 3%). White (maximum level 2%). Blue (maximum level 2%). Orange (maximum level 2%). Yellow 1 (maximum level 2%). Yellow 2 (maximum level 2%). Yellow 3 (maximum level 2%). Green (maximum level 2%). Red 1 (maximum level 2%). Red 2 (maximum level 2%). Brown (maximum level 2%). For use with water up to 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The product is supplied with a stainless-steel braided EPDM lined flexible hose assembly for installation between the solenoid valve and the tap body. The spout outlet incorporates a plastic aerator with built in flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of BS1212-4 diaphragm type inlet valves incorporating a plastic body for use in either side or bottom entry WC cisterns. The valves incorporate an up and over discharge, plastic arm and float. The inlet is fitted with a plastic flow regulator and strainer. Maximum working pressure 10 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Bottom Entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. Incorporates plastic body and ½’’ BSP inlet. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The cistern incorporates an angled servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and NBR seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridges incorporating plastic guides and stem, NBR or EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of single check valve cartridges incorporating a plastic body, stainless steel spring, NBR or EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and silicone seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar Maximum operating temperature 65°C.
Single hole bidet tap with brass body (various finishes) fixed spout outlet and a ceramic disc headwork (various operating members). The outlet incorporates an aerator and the product is supplied with a pop-up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks incorporating a plastic body for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Page 9 of 64
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
