'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Revolve N-307 (5056) Natural'. Natural (appears white), rotationally moulded PE material. For use with water up to 85°C.
'DIC.PPS Z-230-T5 BLACK'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-out spray outlet incorporating a plastic aerator. The spray outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway 98°C, for mixed water pathway 65C and purified water pathway 85°C
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Page 75 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
