'Unecol CINTAS'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'S-9028'. Black coloured, compression moulded EPDM rubber material Shore hardness 60 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EBW-65'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.98mm. For use with water up to 85°C.
'RCI EP 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 65°C.
'HYPRESS12V'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. Between June 2021 and August 2022, the material was for use with water up to 23°C. Between September 2022 and June 2026, the material is for use with water up to 65°C.
'S/EP-50, S/EP-60, S/EP-70 & S/EP-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50A & 80A. Tested in-radius size 1.05mm. For use with water up to 65°C.
'EPDM-W E267'. Black coloured, compression moulded EPDM material. Shore hardness 80A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TEC S147 R.-45 ROSSO'. Orange coloured, injection moulded, silicone rubber 'O' rings & gaskets. Shore hardness 45. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'SB1 Bonding Agent'. Factory applied, black coloured bonding agent intended to bond plastic or brass to rubber. Apply and cure as per manufacturer's instructions 'LDAP-003 issue 1' dated 11-08-2016. For use with water up to 85°C.
'Key Plumb'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DESTONE DSC7500G6'. Black coloured, injection moulded polyketone material. For use with water up to 85°C.
'Novodur® SBM-90 Q203'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
'Novodur® SBM-90'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
Deck mounted single hole, single outlet (fixed) electronically controlled tap assembly (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Tempearture is controlled from a separate control unit incorporating a thermostatic cartridge, which is operated by a single lever on the side of the unit. The spout connects to the unit via a (transparent) PEX-b pipe. The inlets of the control unit incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the unit incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Page 71 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
