'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SIL7018 red & SIL7018 blue'. Red and blue coloured, compression moulded silicone rubber 'O' rings. Shore hardness 70A. Tested in-radius size 2.6mm. For use with water up to 85°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
'ADDISIL IND. 60 E’. Natural (appears white), injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.25mm. For use with water up to 85°C.
'MXLOC 12638, 38 & 48'. Green coloured acrylic based adhesives. Apply as per manufacturer`s instructions. For use with water up to 23°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'‘Welding polymer for Kryoclim®️, Girair®️ and HTA (formerly known as GIRPI HTA Fusion THF Free'. Site applied, orange coloured solvent cement, intended to join PVC-C pipe and fittings. Apply as per pages 4.2 & 4.3 of 'Durapipe HTA®' technical data sheet '04900200 February 2013'. Cure for 24 hours at 7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BUTYL B Membrane'. Black coloured, compression moulded Butyl membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 85°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies, (chromium plated brass body). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Page 635 of 1013
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
