Range of inline plastic bodied ball valves with EPDM ‘O-rings and lever operated. For use with PVC-U pressure pipe in accordance with BS EN 1452 standard Maximum working pressure. Sizes 20mm – 63mm & 1/2" – 2”: 16.0 Bar Sizes 110mm & 2 1/2” – 4”: 10.0 Bar Cold water only
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, incorporating a brass wedge. Valves are operated via a non-rising spindle headwork incorporating either a lockshield or handwheel operating member. Maximum working pressure 20.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass bodies, brass wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (4.5, 6.0 or 8.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
BT1420-DFM Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of scale inhibitors with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43084 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43064 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T43194 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T44014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44054 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44034 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45004 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45014 | BSP 1/2" (F) | 10 bar | 85 °C | Company logo | On operating member | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814110 | chrome | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, | ||
| 814112 | 814112 | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TC28 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28, Production date (DD/MM/YYYY) | Body | No | |||||
| TC28-1 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28-1, Production date (DD/MM/YYYY) | Body | No |
Page 58 of 67
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
