Screw down rising stop valve (nickel plated DZR brass) incorporating a dome type operating member. Maximum working pressure 10.0 Bar Cold water use only
Range of stop valves with brass bodies and T-type operating members. Compression connecitons are for use with copper pipes (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 10.0 Bar Maximum operating temperature 100.0°C
Range of manually operated balancing valves with a DZR brass body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of magnetic scale reducers with metal bodies, for use with copper pipe (manufactured to EN 1057). Maximum working pressure 12 Bar. Maximum operating temperature 30°C.
Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.
'YHR-GFS Enamel'. Factory applied, dark blue coloured Enamel coating. Mix enamel powder with water in a ratio of 7:3 and apply two coats as per manufacturer's TDS 'YHRGFS2504', version 'V0', dated '2025/3/27'. Cure for 20 minutes@120°C and fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the mixing, curing & firing conditions that appear on the approval. If the mix and/or cure and/or fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sealtex ST-2052'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'thoenes BA110'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Sealtex ST-2058'. Blue coloured, Fibre/NBR material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'thoenes BA120'. Blue coloured, fibre/NBR material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'EPLAMID HT00 GFR 40 FW BK'. Black coloured, injection moulded, glass fibre reinforced PA 6T/6I material. For use with water up to 85°C.
'D.63 Spigot and Electrofusion Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 23°C.
'Reno 100'. Black coloured (with blue external stripes), extruded polyethylene pipe. For use with water up to 23°C.
'CP Polytec 80A'. Extruded polyethylene pipe comprising of a blue coloured outer layer and black coloured inner layer. For use with water up to 23°C.
'ELTEX® SUPERSTRESS TUB121N9000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'ELTEX® SUPERSTRESS TUB124N6000'. Blue coloured, compression moulded HDPE material. For use with water up to 23°C.
'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘202968 Tradesave Pipe Sealing Cord TSTPSC160’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.0’, dated 26/11/2025 and this material is only approved for these conditions. For use with water up to 85°C.
Page 550 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
