'XX-CM3'. Factory applied, grey coloured sulphate resistant cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2015'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Interline 925P Off White'. Site applied, two-component, white coloured (once mixed) epoxy coating comprising of Part A (white coloured, opaque paint) and Part B (brown coloured, translucent liquid). Mix Parts A and B in a 4.93:1 mass ratio. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied epoxy resin coatings available in black, blue, grey & red colours. Mix and apply as per technical data sheet dated '12/12/2018'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PAKMEL EP#3500 Series'. Factory applied, grey coloured epoxy coating. Apply as per manufacturer's instructions dated 2020.11.27. Cure for 3 minutes@230°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EDELPOXY FN 132 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's IFU reference 'PC 132' dated 'January 28, 2020'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925P Light Grey'. Site applied applied, two-component, grey coloured (once mixed) epoxy coating comprising of Part A (grey coloured, opaque paint) and Part B (brown coloured, translucent liquid). Mix Parts A and B in a 4.93:1 mass ratio. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White with Ceilcote 680M Primer'. Site applied, white coloured (once mixed), two-component epoxy coating comprising of a two-component primer and two-component top-coat. The primer (Ceilcote 680M) comprises of Part A (uncoloured liquid) and Part B (uncoloured liquid). Mix Parts A and B in a 3:1 volume ratio. Cure for 10 days@30°C. The top-coat (Interline 925 White) comprises of Part A (white coloured, opaque paint) and Part B (white coloured, opaque paste). Mix Parts A and B in a 4.99:1 mass ratio. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MES Precast Tank Concrete Mix'. Factory made, grey coloured concrete & additive. Mix ingredients in the following percentages: Cement 19.10 %, Water 7.56 %, Coarse Aggregate 38.76 %, Fine Aggregate 34.46 %, Plastiment 186 0.03 % & ViscoCrete 0.12 %. Cure for 7 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF2800 & SF2400'. Green coloured, nitrile rubber/aramid material manufactured by calendering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Novus 30'. Orange coloured, nitrile rubber/aramid fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Sealtex ST-2052'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Extrastrong Ivory Coloured (RAL 1015) Tank Panel'. Cream coloured, hot press moulded GRP panel. For use with water up to 50°C.
'GRP-FPI-KSA Fiberstrong'. Pale green coloured (opaque) GRP pipe manufactured by filament winding. Between September 2020 and April 2024 the pipe was for use with water up to 50°C. From May 2024, the pipe is for use with water up to 60°C.
'Aldex C700 & C700F'. Dark brown coloured ion exchange resins. For use with water up to 23°C.
'Aldex C800 Na (16-50 US mesh resin), Aldex C800x10 Na (16-50 US mesh resin), Aldex C800F (Na) (30-70 US mesh resin) & Aldex C800F (K) (30-70 US mesh resin)'. Ion exchange resins which are black coloured except C800F (Na) which is brown coloured. For use with water up to 23°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'Taromid A 260 HW GS10 Black & Taromid A 260 HW GS10 Blue'. Black or blue coloured, injection moulded PA66 materials. For use with water up to 23°C.
'POLYPOL-1005'. Light orange coloured, contact moulded unsaturated polyester resin material. For use with water up to 50°C.
Page 45 of 554
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
