'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo ME'. Amber coloured lubricant to be applied as per manufacturer's instructions '163771', dated April 2016. For use with water up to 60°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 TM-Z1 Alpinweiss 230c'. White coloured, injection moulded, glass fibre reinforced PBT material. In January 2024, 'Badadur PBT9 GF10/GK20 alpinweiss 230c' was added to the approval. Both grades are for use with water up to 65°C.
'Ultrason E 6020 P Natural'. 'Ultrason E2010 G6 Uncoloured’ was added to the approval in September 2022. Natural (appears yellow/brown), injection moulded PESU materials. For use with water up to 85°C.
‘Ultrason® P3010 MR White 20264’. White coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
'NPK PTFE Tape'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'Temprite 88031 PVC-C Fitting'. Light grey coloured, injection moulded PVC-C fitting. For use with water up to 60°C.
`Chemonit 181`. Black coloured, hard rubber material manufactured by roller head extrusion and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'EUW-60'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 0.9mm. For use with water up to 50°C.
'TEC N41-70 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'LP60ANAT 368'. Natural (appears off-white), compression moulded silicone rubber material. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'LSR2650, LSR2660 & LSR2670'. Black coloured, injection moulded liquid silicone rubber materials. Shore hardness between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Loctite® AA 326 with Loctite® SF 7649™ Activator'. Loctite® AA 326 is an amber coloured, liquid anaerobic adhesive and Loctite® SF 7649™ is a green coloured, liquid activator. Apply as per manufacturer's Technical Data Sheet dated December 2013. Cure 7 days@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RIAMAXX HR XE4350 KTW grau R-7040'. Grey coloured, injection moulded, glass filled aliphatic polyketone material. For use with water up to 60°C.
Stop valve with a black plastic body, NBR ‘O’-rings and quarter turn headwork. Maximum working pressure 16.0 bar. Cold water use only.
'Atlas High Pressure Pipe' (formerly known as 'Atlas Pipe'). grey coloured, extruded UPVC pipe. For use with water up to 65°C.
'Atlas Fittings'. Grey coloured, injection moulded UPVC fitting. For use with water up to 65°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet incorporates a flow regulator and the spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated via an infra-red sensor either battery or power supply. The product incorporates a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) battery controlled tap assemblies (chromium plated brass) incorporating approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection .The flow is controlled via a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The tap is supplied with spherical valves for both hot and cold inlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The solenoid is supplied by an isolation valve that incorporates a stainless steel strainer. The spout outlet incorporates a plastic aerator. The product is also supplied with stainless steel braided PEX lined flexible hose assembly for connection to the solenoid valve with ¾” BSP (F) captive nut end connection. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of bottom or side entry BS1212-4 (2016) compact type float operated inlet valves for WC flushing cisterns incorporating plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve and a stainless steel braided PEX lined flexible hose assembly. Maximum working pressure 10.0 bar. Cold water use only.
A range of spring-loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar & maximum operating temperature 65°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Caprice assisted baths which include a choice of with or without a hoist. Flow is controlled via a thermostatic mixing valve supplying the bath spout outlet or shower handset. The discharge from the bath spout and shower handset in via a type AUK 3 airgap, verified by measurement, suitable for Fluid Category 5 backflow protection Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 46°C
Range of low flow rate tap regulators and spray changers, comprising of an EPDM ‘O’-ring, with a stainless-steel strainer housed within a brass body with chrome plated brass trim piece. Maximum working pressure Open outlet use. Maximum operating temperature 85.0°C
Single-hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. Both inlet adaptor connections and the hand-spray inlet incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate that they provide back flow protection. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Single-hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork with a single lever operating member. The product has a pull-out spray outlet which incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The cold inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly, (Chrome plated) brass body incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a pull out spray. The cold inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and models 31 088 000 & 31 183 000 are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator and Model 16 515 xxx is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet, fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The products are supplied with approved click type pop-up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with either (chromium plated or matte black finish brass bodies), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Page 42 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
