Range of pre-set, spring loaded, angled pressure relief valves, with a plastic body and EPDM diaphragm. The B312021 CST model only is pre-set at 4.0 bar, all other models are pre-set at 3.0 bar. The valves are fitted with either rotary type easing gear or hand operated lifting gear. Maximum operating temperature 99°C.
Range of latching and non-latching solenoid valves with brass bodies and an integral stainless-steel strainer. X262513141 (abc) (dd) models have a NBR ‘O’-Ring and diaphragm, all other models have an EPDM ‘O’-Ring and diaphragm. Maximum working pressure: see model. Maximum operating temperatures: X262513141(abc)(dd) models 65°C, all other models 85°C.
Solenoid valve incorporating a plastic body and an EPDM diaphragm. The product incorporates a plastic flow regulator with an EPDM washer, and a plastic filter on the inlet. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Range of brass bodied, straight and angled two and three-port spherical valves. Some models incorporate a screw-down pattern drain valve. Products incorporate a chrome-plated brass ball and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of water conditioners incorporating a static PTFE and zinc anode in a brass or nickel plated bronze body. Between November 2021 and December 2023 the maximum working pressure is: ET/ETD models = 10.0bar, EF/EF-16 models = 16.0 bar, EF-40 models = 40.0 bar. From January 2024 the maximum working pressure is: ET/ETD/EF/EF-16 models = 16.0 bar & EF-40 models = 40.0 bar. Maximum operating temperature 60°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
`CY9198`. Grey coloured, pressed and kilned carbon/graphite thrust ring. For use with water up to 85°C.
'HSL-0588-3 Silicon Coating'. Factory applied, translucent silicon coating. Apply and cure as per manufacturer's instructions version 'BLT19.05 A'. For use with water up to 85°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'EPX-111'. Blue coloured, factory applied epoxy powder coating. Apply and cure as per manufacturer's instructions XL-R-019-R1 dated 2015-11-12'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Orgal® Hydroflex 10'. White coloured, acrylic polymer emulsion cement modifier, which is a liquid additive intended to be mixed with cement to achieve a coating. Mix cement:additive:water in a 197.5:30:10 mass ratio and apply as per manufacturer's instructions '2/18'. Cure for 28 days@23°C and @50% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Flomasta 7619J'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Uneplas Gel Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 5 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
