'XH-S'. Factory applied, grey coloured sulphate resistant Portland cement. Mix sand, cement and water in a 1.5:1.0:0.5 weight ratio. Cure for 3 hours@23-25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tianli 5070 Polyester Epoxy Powder Coating'. Blue coloured, factory applied polyester epoxy powder coating. Apply as per manufacturer's Technical Data Sheet 'V.131130' dated 2013-11-30. Cure for 20 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1600 GRAY AG'. Factory applied, grey coloured epoxy powder paint. Apply as per manufacturer's instructions ref '20210201-1' dated 2021/2/1. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-1'. Factory applied, light grey coloured Portland cement mortar. Mix cement, sand and water in a ratio of 1:1.7:0.55. Cure for 5 hours and 30 minutes@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HSXX CM-1'. Factory applied, grey coloured cement mortar. Mix, apply and cure as per manufacturer's Technical Data Sheet issue number '001' dated '2020.08.01'. For use with water up to 65°C.
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS dated '9 November 2015'. Cure for 210 seconds@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fastfill'. Site applied, grey coloured cementitous mortar. Mix Fastfill and water in a 7.14:1 mass ratio. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nexseal Waterproofing Admixture'. Site applied, white coloured (opaque) waterproofing admixture in the form of a powder. Admixture to be added to cement in a dosing ratio of 1kg/m³. Wet cure for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YHCM-01'. Factory applied, grey coloured sulphate resisting cementitious mortar. Mix sand, cement & water in a ratio of 1: 2.5: 0.3. Cure for 4 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'IKV Tribostar SSI 1203TF/IKV Tribofood SSI 1203TF'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Grasso L. 100 Lubricating Grease'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'FYPBK-01 PE Pipes Black & Blue'. Extruded, HDPE pipes which are either black coloured (with blue, external stripe) or blue coloured. For use with water up to 65°C.
'FYFBK-01 PE Fittings Black & Blue'. Injection moulded, HDPE fittings which are either black coloured or blue coloured. For use with water up to 65°C.
Dowlex NG2432UE. Dowlex NG2432.10UE. RX 103 Natural. RX 103 Black 9003. RX 103 GR Black 9003. Natural and black coloured, rotationally moulded polyethylene material. For use with water up to 70°C.
'TP10847 Prisma Black'. Black coloured polyethylene material manufacture by rotational moulding. For use with water up to 70°C.
'Purithon PPSU P5010 NC (natural, appears brown coloured), P5010 WH (white coloured), P5010 BK (black coloured), P5010 GY (grey coloured) & P5010 BL (blue coloured)'. Injection moulded PPSU materials. For use with water up to 85°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
Page 34 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
