Range of pilot operated pressure reducing valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and O-rings. The products are supplied with auxiliary fittings: spherical valves, pressure gauges, a pilot valve, a needle valve and stainless steel tubes. The DN400 model also includes a Y-pattern strainer. Maximum inlet supply pressure 16.0 bar. The outlet pressure is adjustable between 0.7~16.0 bar. Maximum operating temperature 65°C.
Range of spherical valves incorporating brass bodies and ball. Maximum working pressure see models. Maximum operating temperature 100°C.
Range of press fit spherical valves with brass bodies, stainless steel balls and PTFE seats. The valve are available with lever, extended lever, lockshield lever and butterfly handle operating members. For use with copper pipe (manufactured to EN1057) and stainless-steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ or ‘V’ profile (model dependent). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges, incorporating a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated ductile iron gate valves with an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of DZR brass combination valves consisting of an in-line adjustable pressure reducing valve (2.1 - 16.0 bar for ILG22-2 model and 1.4 - 6.0 bar for all other models), a pressure relief valve (set @ 6.0 bar) and EPDM gaskets and ‘O’-rings. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 90°C.
Range of double regulating valves available with bronze bodies, incorporating a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'Super Poxy 505TL'. Factory applied, grey coloured, two-component Epoxy coating. Mix Parts A & B in a 100:20 weight ratio and apply as per manufacturer's TDS dated '2026.01.14'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Nitomortar TC2000'. Factory applied, two-component, grey coloured (once mixed and applied) epoxy resin sealing compound. The material is supplied in pre-weighed quantities (60% base, 40% hardener), to be applied in accordance with manufacturer's instructions 'FO SA/NITOMORTAR TC2000/0110/19'. Cure for 7 days@25°C and 55% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DUAYEN ANTIBLAST GEÇIRIMSIZ SPREY BOYA KAPLAMA'. Factory applied, two-component, black coloured (once mixed and applied), Polyurea coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's TDS 'Rev01', date of issue '22.04.2024'. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP TANK 500 PW'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a 3:1 volume ration and apply two coats as per manufacturer's TDS '0724'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate to 40°C and then spray apply as per manufacturer's instructions issued ‘March 2017, V4.1’. Cure for 20 minutes@180°C. For use with water up to 85°C.
‘Intergard 269’ primer for use with ‘Interline 975’ coating. Site applied, off-white coloured (once mixed and applied) epoxy coating system comprising of a two-part primer and two-part topcoat. Mix parts A & B of ‘Intergard 269’ primer in a 4:1 volume ratio and apply as per manufacturer’s TDS reference ‘206’, dated ‘11/03/2016’. Cure for 24 hours@10°C. Mix parts A & B of ‘Interline 975’ coating in a 2.2:1 volume ratio and apply as per manufacturer’s TDS reference ‘4236’, dated ‘04/02/2015’. Cure for 14 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Safecure Super’. White coloured, spray applied SBR latex solution intended to act as a concrete curing membrane. Apply as per manufacturer`s 'Tech Data Sheet no. 306', 'Revision no. v4', dated '02.01.2026'. Cure for 14 days at 25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Grilamid TR ICR 12 LS natural' (appears white, transparent), 'Grilamid TR ICR 12 LS yellow 6908' (yellow coloured) and 'Grilamid TR ICR 12 LS blue 4271' (blue coloured). Injection moulded PA MACM12/X materials. For use with water up to 85°C.
Hostalen 4731B HDPE-HT. White coloured, extruded polyethylene material. For use with water up to 60°C.
'Repair Stick Steel' & 'Repair Stick Stainless Steel'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per manufacturer’s TDS dated 17.09.2025. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemiline AE 004 FB 26'. Black coloured, butyl material manufactured by calendaring. Shore hardness 65A. Tested in-radius size 1.0mm. For use with water up to 65°C.
Page 310 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
