Range of salt regenerated ion exchange water softeners for domestic use. The gearbox assembly and each elbow assembly incorporate a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Cold water use only.
'JSGL-SRC (U)'. Factory applied, grey coloured Sulphate resistant cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (E)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (U)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ULTRAMID® D3EG12 AQUA BLACK 102'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'PE 7144 Plastic Sleeve'. Natural (appears white), injection moulded polyethylene component. For use with water up to 85°C.
'Wefatherm PP-RCT Pipe'. Green coloured, extruded PP-RCT pipe. For use with water up to 85°C.
'Wefatherm PP-RCT Fitting'. Green coloured, injection moulded PP-RCT fitting. For use with water up to 85°C.
'ME0940 'O' rings'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 5.0mm. For use with water up to 85°C.
'EPDM 70: Blaco_Water/Food-EE70’. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70 A. Tested in-radius size 0.75mm. For use with water up to 85°C.
'EPDM B1-4771'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-out spray outlet incorporating a plastic aerator. The spray outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway 98°C, for mixed water pathway 65C and purified water pathway 85°C
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of ceramic disc headworks with brass bodies. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure - 10 Bar Maximum operating temperature - 85 °C
Range of thermostatic cartridges with either brass or plastic bodies, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The outlet is a pull-down spray type and incorporates a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) pullout spray combination tap assembly (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click-type pop up waste (not verified by test). Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Page 296 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
