'Sigmaguard CSF 585/Blue' (included on the initial approval) is for use with water up to 50°C. 'Sigmaguard CSF 585/RAL5017’ was added to the approval in December 2025 and is for use with water up to 40°C. Factory applied, blue coloured, two-component, solvent-free epoxy coatings. Mix parts A & B in a volume ratio of 77.5:22.5 and apply as per manufacturer's Product Data Sheet '7785', dated 'August 19, 2022'. Cure for 12 days@20°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SJ-195120WT GRP Panel'. Off-white coloured, compression moulded GRP panel. For use with water up to 50°C.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
Range of single-hole, single outlet (fixed) electronically operated, tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by a touch sensor. The spout outlets incorporate plastic aerators. Max working pressure 8.0 bar. Max operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve that is activated via an infrared sensor. The spout outlet incorporates an aerator. Maximum working pressure: 8.0 Bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure - 8 Bar. Maximum operating temperature - 65 °C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled with a solenoid valve activated via touch operation. The spout outlets incorporate plastic aerators and the flexible hoses incorporate a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled with a solenoid valve activated via touch operation. Temperature is controlled using a manual single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate an approved check valve cartridge; however the complete assemblies have not been fully tested to demonstrate they provide backflow protection, and a stainless steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of quarter turn Ceramic disc headworks with brass bodies incorporating NBR rubber seals. For insertion into specifically dimensioned bores Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of single hole, single outlet, (swivel), combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The outlet is a pull-down spray type and incorporates a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure; 5 Bar Maximum operating temperature 65°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a single sequential cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever type operating member. The spout outlet incorporates a plastic aerator and flow regulator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 193838 X XXX | VARIOUS | 1/2" BSP | 10 bar | 65 °C | PPI | Body | No | Ceramic cartridge | C Clamp | Aerator | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Page 30 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
