'FC941'. Black coloured, injection moulded, carbon graphite bearing. For use with water up to 85°C.
'CS15 & LF1'. Dark grey coloured, pressed and sintered silicon carbide ceramic materials. For use with water up to 85°C.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
‘PVEF undercoat with Fluiglide Topcoat’. Factory applied, cream coloured (once mixed and applied), coating system comprising of ‘Polyglass VEF’, two-component glassflake vinyl ester undercoat and ‘Fluiglide’, two-component polyester topcoat. Mix and apply ‘Polyglass VEF’ in accordance with Corrocoat ‘product reference 2/23’ dated ‘5th June 2007’ and last reviewed ‘March 2022’. Cure for 24 hrs@20°C (±1°C). Mix and apply ‘Fluiglide’ in accordance with Corrocoat ‘product reference ‘4/01’, valid from ‘23rd October 1995’ and last reviewed ‘March 2022’. Cure for a minimum of 6 days@20°C (with a lower tolerance of -1°C). For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard DT High Build Finish Epoxy Coating'. Factory applied, two-component, grey coloured epoxy coating. Mix and apply as per manufacturer's instructions ‘Document Ref : SPL/R&D/TTD/UI/001, Issue No.01, Version: 01’ dated 01.11.2015. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'Vinoleo ME'. Amber coloured lubricant to be applied as per manufacturer's instructions '163771', dated April 2016. For use with water up to 60°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
`Pocan B1501 000000`. Natural (appears white coloured), injection moulded PBT material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 TM-Z1 Alpinweiss 230c'. White coloured, injection moulded, glass fibre reinforced PBT material. In January 2024, 'Badadur PBT9 GF10/GK20 alpinweiss 230c' was added to the approval. Both grades are for use with water up to 65°C.
'Ultrason E 6020 P Natural'. 'Ultrason E2010 G6 Uncoloured’ was added to the approval in September 2022. Natural (appears yellow/brown), injection moulded PESU materials. For use with water up to 85°C.
'Georg Fischer HDPE PE100 Black Machined Fabricated Fittings and Segmented Fabricated Fittings'. Black coloured, HDPE PE100, machined fabricated fittings. Black coloured, with or without blue stripe, extruded and fabricated, HDPE PE100 fabricated segmented fittings. For use with water up to 60°C.
‘Kingbull PE100 blue pipe (391721)'. Blue coloured, extruded polyethylene pipe. ‘Kingbull PE100 black pipe’ (0103102). Black coloured (with external blue stripe), extruded polyethylene pipe. Both for use with water up to 65°C.
'HDPE 100 Black POLIMAXX P901BK'. Black coloured, extruded HDPE pipe. For use with water up to 65°C.
'HDPE 100 Blue POLIMAXX P901BL'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'Protecta-line Pipes PE80 & PE100 Pipes'. Extruded, multi-layered pipes comprising of a black coloured PE80 or PE100 inner layer, aluminium middle layer and blue coloured PE80 or PE100 outer layer. The pipes have a black external stripe. For use with water up to 23°C.
'Steel Stick'. Reinforced epoxy repair putty which comprises of a black coloured core surrounded by a light grey coloured stick. Knead the core and stick together until an even colour (dark brown) and consistency is achieved and apply as per manufacturer's instructions of use dated 31/03/2022. Cure for 20 minutes@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9711/2 Black'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radii sizes between 0.88mm & 2.85mm. Between October 2021 and July 2022, the components were for use with water up to 23°C. Between August 2022 and October 2026, the components are for use with water up to 85°C.
'E51-70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EUW-75'. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EUW-80'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'TEC N41-70 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'SIL8701 Red 'O'-rings'. Red coloured, injection moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
‘Silopren LSR 2030, 2040, 2050, 2060, 2070 & 2080’. Natural (appears clear), compression moulded silicone rubbers with a shore hardness between 30 and 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'LSR2650, LSR2660 & LSR2670'. Black coloured, injection moulded liquid silicone rubber materials. Shore hardness between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Adey MCXS Clear'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet 'issue 1' dated 03/03/2022. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikasil DW Trans'. Site applied silicone sealants available in transparent (CO0 transparent), grey (RA1 7004) or black (CO4 Schwarz). Apply as per manufacturer's instructions Product Data Sheet 'April 2022, Version 04.01'. Cure for 24 hours@7°C. The transparent (CO0 transparent) and grey (RA1 7004) sealants are for use with water up to 85°C. The black (CO4 Schwarz) sealant is for use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Loctite® AA 326 with Loctite® SF 7649™ Activator'. Loctite® AA 326 is an amber coloured, liquid anaerobic adhesive and Loctite® SF 7649™ is a green coloured, liquid activator. Apply as per manufacturer's Technical Data Sheet dated December 2013. Cure 7 days@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted electric showers (various finishes). The GSD/BETTER models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/DSK/ENTRY models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). Incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). The GSD models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/ models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (various finishes), incorporating an electronic cartridge controlling the flow which is activated via an infrared sensor (either battery or mains powered). Models 31 171 xxx & 31 173 xxx incorporates a manually operated temperature control. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet incorporates a flow regulator and the spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated via an infra-red sensor either battery or power supply. The product incorporates a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bottom or side entry BS1212-4 (2016) compact type float operated inlet valves for WC flushing cisterns incorporating plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve and a stainless steel braided PEX lined flexible hose assembly. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
A range of spring-loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar & maximum operating temperature 65°C.
Page 29 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
