Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN 1057. Maximum working pressure; 16.0 Bar. Maximum operating temperature 85oC

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241002061

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models below, note, all models use M crimp profiles.

Marking:

Navigator logo and size on body.

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

PFWC-15 = PRESSFIT WATER 15mm Coupling PFWC-22 = PRESSFIT WATER 22mm Coupling PFWC-28 = PRESSFIT WATER 28mm Coupling PFWC-35 = PRESSFIT WATER 35mm Coupling PFWC-42 = PRESSFIT WATER 42mm Coupling PFWC-54 = PRESSFIT WATER 54mm Coupling PFWCS-15 = PRESSFIT WATER 15mm Slip Coupling PFWCS-22 = PRESSFIT WATER 22mm Slip Coupling PFWCS-28 = PRESSFIT WATER 28mm Slip Coupling PFWCS-35 = PRESSFIT WATER 35mm Slip Coupling PFWCS-42 = PRESSFIT WATER 42mm Slip Coupling PFWCS-54 = PRESSFIT WATER 54mm Slip Coupling PFWRC-2215 = PRESSFIT WATER 22x15mm Reducing Coupler PFWRC-2815 = PRESSFIT WATER 28x15mm Reducing Coupler PFWRC-2822 = PRESSFIT WATER 28x22mm Reducing Coupler PFWRC-3522 = PRESSFIT WATER 35x22mm Reducing Coupler PFWRC-3528 = PRESSFIT WATER 35x28mm Reducing Coupler PFWRC-4222 = PRESSFIT WATER 42x22mm Reducing Coupler PFWRC-4228 = PRESSFIT WATER 42x28mm Reducing Coupler PFWRC-4235 = PRESSFIT WATER 42x35mm Reducing Coupler PFWRC-5435 = PRESSFIT WATER 54x35mm Reducing Coupler PFWRC-5442 = PRESSFIT WATER 54x42mm Reducing Coupler PFWFR-3528 = PRESSFIT WATER 35x28mm Fittings Reducer PFWFR-4222 = PRESSFIT WATER 42x22mm Fittings Reducer PFWFR-4228 = PRESSFIT WATER 42x28mm Fittings Reducer PFWFR-4235 = PRESSFIT WATER 42x35mm Fittings Reducer PFWFR-2215 = PRESSFIT WATER 22x15mm Fittings Reducer PFWFR-2815 = PRESSFIT WATER 28x15mm Fittings Reducer PFWFR-2822 = PRESSFIT WATER 28x22mm Fittings Reducer PFWFR-3522 = PRESSFIT WATER 35x22mm Fittings Reducer PFWFR-5428 = PRESSFIT WATER 54x28mm Fittings Reducer PFWFR-5435 = PRESSFIT WATER 54x35mm Fittings Reducer PFWFR-5442 = PRESSFIT WATER 54x42mm Fittings Reducer PFWEC-15 = PRESSFIT WATER 15mm End Cap PFWEC-22 = PRESSFIT WATER 22mm End Cap PFWEC-28 = PRESSFIT WATER 28mm End Cap PFWEC-35 = PRESSFIT WATER 35mm End Cap PFWEC-42 = PRESSFIT WATER 42mm End Cap PFWEC-54 = PRESSFIT WATER 54mm End Cap PFWET-15 = PRESSFIT WATER 15mm Equal Tee PFWET-22 = PRESSFIT WATER 22mm Equal Tee PFWET-28 = PRESSFIT WATER 28mm Equal Tee PFWET-35 = PRESSFIT WATER 35mm Equal Tee PFWET-42 = PRESSFIT WATER 42mm Equal Tee PFWET-54 = PRESSFIT WATER 54mm Equal Tee PFWE-15 = PRESSFIT WATER 15mm 90° Degree Elbow PFWE-22 = PRESSFIT WATER 22mm 90° Degree Elbow PFWE-28 = PRESSFIT WATER 28mm 90° Degree Elbow PFWE-35 = PRESSFIT WATER 35mm 90° Degree Elbow PFWE-42 = PRESSFIT WATER 42mm 90° Degree Elbow PFWE-54 = PRESSFIT WATER 54mm 90° Degree Elbow PFWES-15 = PRESSFIT WATER 15mm 90° Degree Street Elbow PFWES-22 = PRESSFIT WATER 22mm 90° Degree Street Elbow PFWES-28 = PRESSFIT WATER 28mm 90° Degree Street Elbow PFWES-35 = PRESSFIT WATER 35mm 90° Degree Street Elbow PFWES-42 = PRESSFIT WATER 42mm 90° Degree Street Elbow PFWES-54 = PRESSFIT WATER 54mm 90° Degree Street Elbow PFWE/45-15 = PRESSFIT WATER 15mm 45° Degree Elbow PFWE/45-22 = PRESSFIT WATER 22mm 45° Degree Elbow PFWE/45-28 = PRESSFIT WATER 28mm 45° Degree Elbow PFWE/45-35 = PRESSFIT WATER 35mm 45° Degree Elbow PFWE/45-42 = PRESSFIT WATER 42mm 45° Degree Elbow PFWE/45-54 = PRESSFIT WATER 54mm 45° Degree Elbow PFWES/45-15 = PRESSFIT WATER 15mm 45° Degree Street Elbow PFWES/45-22 = PRESSFIT WATER 22mm 45° Degree Street Elbow PFWES/45-28 = PRESSFIT WATER 28mm 45° Degree Street Elbow PFWES/45-35 = PRESSFIT WATER 35mm 45° Degree Street Elbow PFWES/45-42 = PRESSFIT WATER 42mm 45° Degree Street Elbow PFWES/45-54 = PRESSFIT WATER 54mm 45° Degree Street Elbow PFWRT-221515 = PRESSFIT WATER 22x15x15mm Reducing Tee PFWRT-221522 = PRESSFIT WATER 22x15x22mm Reducing Tee PFWRT-282222 = PRESSFIT WATER 28x22x22mm Reducing Tee PFWRT-282228 = PRESSFIT WATER 28x22x28mm Reducing Tee PFWRT-222215 = PRESSFIT WATER 22x22x15mm Reducing Tee PFWRT-282815 = PRESSFIT WATER 28x28x15mm Reducing Tee PFWRT-282822 = PRESSFIT WATER 28x28x22mm Reducing Tee PFWRT-353515 = PRESSFIT WATER 35x35x15mm Reducing Tee PFWRT-353522 = PRESSFIT WATER 35x35x22mm Reducing Tee PFWRT-353528 = PRESSFIT WATER 35x35x28mm Reducing Tee PFWRT-424215 = PRESSFIT WATER 42x42x15mm Reducing Tee PFWRT-424222 = PRESSFIT WATER 42x42x22mm Reducing Tee PFWRT-424228 = PRESSFIT WATER 42x42x28mm Reducing Tee PFWRT-424235 = PRESSFIT WATER 42x42x35mm Reducing Tee PFWRT-545422 = PRESSFIT WATER 54x54x22mm Reducing Tee PFWRT-545428 = PRESSFIT WATER 54x54x28mm Reducing Tee PFWRT-545435 = PRESSFIT WATER 54x54x35mm Reducing Tee PFWRT-545442 = PRESSFIT WATER 54x54x42mm Reducing Tee

Approval Holder:

Navigator MSL Ltd.

Company Name

Navigator MSL Ltd.

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

General Email

sales@navigatormsl.com

View All Listings by this Company

FLOMASTA range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2207402

Note:

For above and below ground use

Size:

20mm – 63mm.

Marking:

Flomasta, WRAS, PN & size on nut.

Installation Requirements:

R001

Expiry date:

31/07/2027

Model:

FLOMASTA compression fittings 20-63mm 320*****U ADAPTOR MALE FLOMASTA 320A*****U ADAPTOR FEMALE FLOMASTA 320B*****U END PLUG FLOMASTA 320C*****U FLANGED ADAPTOR FLOMASTA 320D*****U FLANGED ADAPTOR (4 BOLTS)FLOMASTA 321******U COUPLING FLOMASTA 321A*****U REDUCING COUPLING FLOMASTA 321B*****U REPAIR COUPLING FLOMASTA 322******U ELBOW 90 FLOMASTA 322A*****U ELBOW THREADED MALE FLOMASTA 322C*****U ELBOW FEMALE for POP-UP FLOMASTA 322B*****U ELBOW THREADED FEMALE FLOMASTA 322D*****U WALL ELBOW COMPRESSION FLOMASTA 323******U TEE THREADED FEMALE FLOMASTA 323A*****U TEE THREADED MALE FLOMASTA 324******U TEE 90° ELYSEE FLOMASTA 324A*****U TEE REDUCING FLOMASTA 321C*****U UNIVERSAL ADAPTOR FLOMASTA Where XXX-YYY-ZZZ for product family cocdes with only 3 digits 330 (standard code prefix) – yyy (1st end diameter) -zzz (2nd end diameter) Xxx(x)-yyy-zz for product family codes with e altter as a firth digit 330A (A standard code) – (063) yyy diameter – (06) zz threaded diameter.

Approval Holder:

Kingfisher International Products Ltd

Company Name

Kingfisher International Products Ltd

Address

1 Paddington Square, London

Postcode

W2 1GG

Phone

07721 260713

General Email

eric.capotummino@kingfisher.com

View All Listings by this Company

Indirect heat interface unit with copper brazed, stainless-steel heat exchangers, providing heating and instantaneous hot water. The product incorporates an expansion vessel on the cold-water supply to the plate heat exchanger and a safety relief valve on the heating circuit set @ 2.5 bar. The DHW and heating circuits are both fitted with drain valves incorporating cover caps. Maximum working pressure 16 Bar (Primary), 10 Bar (DHW) & 3 Bar (Heating) Maximum operating temperature 95°C

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/4” BSP (M)

Marking:

YGHP, serial number, pressure, temperature and other technical information on adhesive label inside body

Installation Requirements:

R001 R140 R360 R511

Expiry date:

31/10/2029

Model:

YGHP E 018

Manufacturer:

YGHP Ltd

Company Name

YGHP Ltd

View All Listings by this Company

‘PREMIX’ range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both the domestic hot water and primary circuit are controlled via spherical valves. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 80°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

240904726

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression (Primary Circuit) 15mm compression (Secondary Circuit)

Marking:

E.C.A. on front cover. E.C.A, model and technical information including KW rating on adhesive label on body.

Installation Requirements:

R001 R360

Expiry date:

30/09/2029

Model:

8116350010 CALORA PREMIX 24 HM ERP UK 8116484110 CALORA PREMIX 14 HM ERP UK 8116487110 CALORA PREMIX 20 HM ERP UK 8116356010 CALORA PREMIX 28 HM ERP UK 8116389010 CITIUS PREMIX 14 HM ERP UK 8116392010 CITIUS PREMIX 20 HM ERP UK 8116353010 CITIUS PREMIX 24 HM ERP UK 8116380010 CITIUS PREMIX 28 HM ERP UK 8116576110 Proteus Premix 42 HM DG ERP UK 8116550010 Proteus Premix 45 HM DG ERP UK

Approval Holder:

Emas Makina Sanayi A.S.

Company Name

Emas Makina Sanayi A.S.

Address

Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa

Postcode

45030

Country

Turkey

General Email

egecakmakci@emas.com.tr

View All Listings by this Company

Manufacturer:

Emas Makina Sanayi A.S.

Company Name

Emas Makina Sanayi A.S.

Address

Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa

Postcode

45030

Country

Turkey

General Email

egecakmakci@emas.com.tr

View All Listings by this Company

Range of in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) to 1½” BSP (M)

Marking:

ZENNER on cover. Flow arrow on body. Zenner and product info on meter face.

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

IUWS hydr. 2,5-110-1/2 D-cell IUWS hydr. 2,5-165-1/2 D-cell IUWS hydr. 2,5-170-1/2 D-cell IUWS hydr. 2,5-190-1/2 D-cell IUWS hydr. 4-105-3/4 D-cell IUWS hydr. 4-130-3/4 D-cell IUWS hydr. 4-165-3/4 D-cell IUWS hydr. 4-190-3/4 D-cell IUWS hydr. 4-220-3/4 D-cell IUWS hydr. 10-150-1 D-cell IUWS hydr. 10-160-1 D-cell IUWS hydr. 10-160-5/4 D-cell IUWS hydr. 10-260-5/4 D-cell IUWS hydr. 16-150-6/4 D-cell IUWS hydr. 16-200-6/4 D-cell IUWS hydr. 16-300-6/4 D-cell IUWS hydr. 25-300-2 D-cell

Approval Holder:

Zenner International Gmbh & Co. KG

Company Name

Zenner International Gmbh & Co. KG

Address

Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany

Country

Germany

View All Listings by this Company

Manufacturer:

Zenner Meters (Shanghai) Ltd.

Company Name

Zenner Meters (Shanghai) Ltd.

Address

No 15 Dongxing Road Songjiang Ind Zone Shanghai

Country

China

View All Listings by this Company

Range of in-line water meters with plastic bodies. The inlet incorporates a plastic filter. Maximum working pressure; 16 Bar Maximum operating temperature 50°C

Section:

1505 Water Meters

WRAS Approval Number:

240902075

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

All models available in body lengths of 165, 170 and 190mm

Size:

1" BSP (M)

Marking:

Contazara, Model and technical information on faceplate. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

CZ4000- Q3=4

Approval Holder:

Contadores De Agua De Zaragoza S.A. (Contazara S.A.)

Company Name

Contadores De Agua De Zaragoza S.A. (Contazara S.A.)

Address

Carretera Castellon KM. 5 5 50720 Zaragoza Spain

View All Listings by this Company

Range of in-line water meters with brass bodies and plastic turbines. The inlets incorporate plastic filters, and the outlets incorporate non-return valves (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 65.0°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M) ¾” BSP (M 1¼” BSP M, 1½” BSP M, 2” BSP

Marking:

Janz logo, model code and other info on meter box

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

Smartio DN15 Q3=2,5 R*** Smartio DN20 Q3=2,5 R*** Smartio DN20 Q3=4 R*** Models added August 2025: Smartio DN25 Q3=6,3 R*** Smartio DN32 Q3=10 R*** Smartio DN40 Q3=16 R*** Body lengths: DN25: 150mm/160mm/175mm/198mm*/220mm*/260mm* DN32: 150mm/160mm/200mm*/220mm*/260mm* DN40: 150mm/200mm/300mm* *It’s possible to put a non-return valve (NRV)

Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

Company logo, Made in Italy, temperature and pressure cast on body.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

54DM15000 & 54DM15000XX Stopshock xx (Packaging variation)

Approval Holder:

Barberi Rubinetterie Industriali Srl

Company Name

Barberi Rubinetterie Industriali Srl

Address

Via Monte Fenera 7 13018 Valduggia Italy

Phone

+39 163 48 284

General Email

barberi@barberi.it

View All Listings by this Company

Manifold with a brass body and 5 outlets. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Marking:

1” Elviom on body

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

589403400051

Approval Holder:

Interplast SA

Company Name

Interplast SA

Address

Komotini Industrial Zone, Komotini P.C. 69100

Country

Greece

View All Listings by this Company

Range of leak detection devices incorporating a DZR brass body and non-return valve (not intended for and not suitable for backflow protection). Models 3897590 & 3897690 incorporate a spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

RBM, flow arrow, PN & CR on body. RBM and product info on control unit.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

3897590: 1: ¾” BSP (M) 3897690: 2: 1” BSP (M) 37880620: 1” BSP (M) x ¾” BSP (M) reducer

Approval Holder:

RBM S.p.a.

Company Name

RBM S.p.a.

Address

Componenti Per Impianti Idrotermici Via S. Giuseppe, 1 25075 Nave (Brescia)

Country

Italy

View All Listings by this Company