Range of spherical valves with UPVC bodies and balls, incorporating EPDM seals & `O` rings. Maximum working pressure 16.0 Bar (3101-99BBE to 3101-05BBE) or 10.0 Bar (3101-06BBE to 3101-08BBE, All 3101-XXAAE & all 3101-XXLLE models Cold water use only
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange pressure rating). Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 16.0 bar and a maximum operating temperature 85°C.
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges, EPDM gasket and ‘O’-ring. The valves operate via non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50: 25.0 bar, DN65-DN600: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of automatic thermal balancing valves (DZR Brass) with non-rising spindle headwork, brass disc and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Magnetic scale reducers, incorporating chrome plated copper body, for use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
'WY-01~-04'. White coloured (opaque), moulded and sintered ceramic material. For use with water up to 85°C.
'CER18635 Ceramic Ring'. White coloured (opaque), sintered, ceramic ring. For use with water up to 85°C.
'DX101, DX201, DX202 & DX203 Rings'. Dark grey coloured, compression moulded silicon carbide ring components. For use with water up to 85°C.
‘Purethane® NXT’. Factory applied, two-component, natural (appears off-white) polyurethane coating. Mix resin and activator in a 2.5:1 volume ratio and apply as per manufacturer’s instructions 'APP-CA-NXT-Rev 03' dated 01.04.2017. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Euronavy Engineering EW0100'. Factory applied, two-pack white coloured (once mixed) epoxy coating. Mix and apply as per manufacturer's TDS edition 'February 2023'. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMALINE 855 (11) Blue'. Factory applied, blue coloured, two-component polyurethane coating. 'SIGMALINE 855 (11) Blue' is for use with water up to 23°C. In September 2024 ‘SIGMALINE 855 (11) Off White’ was added to the approval. Off-white coloured two-component polyurethane coating. 'SIGMALINE 855 (11) Off White' is for use with water up to 36°C. Mix and apply as per manufacturer's Product Data Sheet ‘7656’, dated 'September 16, 2024'. Cure for 12 hours@20°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CSJX53-2 Red'. Factory applied, red coloured polyacrylic resin coating. Apply as per manufacturer's instructions file no. ‘CSJ-0016-1’, version no. ‘A1’, dated 2016.10.12. Cure for 50 minutes@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 258 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
