Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
‘MagCat’ range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Activflo Lite range of water conditioners with copper bodies. Models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
“CN Pressure vessel” range incorporating a HDPE liner. The products have a separate outer layer (with black, blue, grey or natural finishes). The CN Pressure vessel 24x72” D-4 model has a top and bottom opening. Maximum operating pressure 10.5 bar. Cold water use only.
'KH369R'. Black coloured, compression moulded Carbon ring which is impregnated with Phenolic Resin. For use with water up to 85°C.
'Relithane 151. Factory applied, brown coloured, two-component Polyurethane coating. Mix base and hardener in a 2.5:1 ratio and apply as per manufacturer's 'Standard Operating Procedure & Guidelines, Revision 2, 157/2022' dated 12th October 2022. Cure for 40 seconds@35°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SUS-GRP01'. White coloured GRP panel manufactured by hot press moulding. For use with water up to 65°C.
'Neama Liner Sand Filter'. Off-white coloured (translucent), rotationally moulded LLDPE filter. For use with water up to 65°C.
'Cosmoplast UPVC Pressure Fitting D3 Compound'. Grey coloured, injection moulded UPVC fittings. For use with water up to 65°C.
'WRAS 61713 EB 78'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 78D. Tested in-radius size 1.05mm. For use with water up to 60°C.
'SME001 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 60. In November 2024 'SME001 EPDM', a compression moulded EPDM rubber with a shore hardness of 75 was added to the approval so that a range with a hardness between 60 & 75 is covered by the approval. Tested in-radius size of 1.0mm and are for use with water up to 65°C.
'PVCC125 & PVCC250 PVC Pipe Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 24012024'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EFFAST Large Tite PVC Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6310925/20'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EFFAST PRESSURE PVC Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6313369/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Durapipe RH PVC-U Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6311355/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 243 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
