Range of gate valves with blue epoxy powder coated, ductile iron wedge and bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.
‘Sleeve for Pipe M. Bottom Filter Nozzles DM, DS & D8. Upper Filter Nozzles AD, AP, AM & AS. Collector CB06, CB08, CC06 & CC12. Filter Nozzles P6 & P5’. Natural (appear white in colour) & red coloured, injection moulded ABS components. For use with water up to 23°C.
Carbongraphite AG21 P/T, MCI320/T & AG21P-3M/T. Dark grey coloured, phenolic resin filled, carbon graphite rings manufactured by cold pressing. For use with water up to 85°C.
'MAT901 & MAT902'. Black coloured carbon/PTFE washer manufactured by pressing. For use with water up to 85°C.
'S' Cement. Factory applied, grey coloured cement, intended to line ductile iron pipes. Mix cement and sand in a weight ratio of 33:67. Cure for 28 days@28°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'JSP-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
‘SIKALASTIC-836 DW & SIKAFLOOR 150’. Factory applied, off-white coloured (once mixed and applied), two-part polyurea coating system. ‘SIKAFLOOR 150’ is a two-component epoxy primer which is to be mixed in a 74:26 weight ratio and applied in accordance with manufacturer’s Product Data Sheet version ‘8’, dated May 2022. ‘SIKALASTIC-836 DW’ is a two-component polyurea coating which is to be mixed in a 1:1 volume ratio and applied in accordance with manufacturer’s Product Data Sheet version ’03.0’, dated January 2021. Cure for 24 hours at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ePIPE® UK'. Site applied, red-brown coloured, two-part epoxy based coating consisting of a based and activator. Mix base and activator in a 2:1 mass ratio and apply as per manufacturer's IFU issue '009', dated March 23, 2011. Air-cure for 60 minutes@25°C and then immerse in a water bath at 60°C for 60 minutes. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Myungjin GRP Water Tank Panel'. Light grey coloured, hot pressed GRP panel. For use with water up to 50°C.
'4MID 9B22150 W-A BBK'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
"Reinert-Ritz PE 100 Fittings". Black coloured, extruded polyethylene fittings. For use with water up to 85°C.
'Jain HDPE (PE 100) Blue Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'Jain HDPE (PE 100) Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
‘Dowlex 2631UE & Dowlex 2631.10UE’ Natural (appear white coloured). ‘RX 102 Natural, RX 102 Black 9003 & RX 102 GR Black 9003’ (black coloured). In April 2025 ‘RX102 Blue 6263’ (blue coloured) was added to the approval. Rotationally moulded polyethylene materials. For use with water up to 70°C
‘Dowlex 2629UE & Dowlex 2629.10UE’. ‘RX 101 Natural, RX 101 Black 9003 & RX 101 GR Black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
Page 215 of 554
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
