Range of gate valves with blue epoxy coated ductile iron bodies, EPDM wedge and a non-rising spindle. Maximum working pressure 16.0. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with bronze bodies, brass bonnets and DZR brass stems . The valves operate via a spindle headwork with hand wheel operation. Threaded end connections to BS21 ISO 7 /1 r/c (BSP Taper - JIS B0203). Maximum working pressure 25.0 bar. Maximum operating temperature 23oC.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
‘Series 116’ range of balancing valves (DZR Brass body). Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
Range of commercial, salt regenerated, electronically controlled ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
Electronically controlled, commercial ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (natural, appear white)'. 'Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials. For use with water up to 85°C.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9001 Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's TDS/IFU 'number: 001', 'First Edition', revision date 'March 20, 2025'. Cure for 60 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-LM'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no. BSS-LM-D0001', 'Date: 9.20.2025'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.1 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver 1 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyglass VEF'. Factory applied, two-part, off-white coloured, vinyl ester coating. Mix parts A & B in a 98:2 mass ratio and apply as per manufacturer's instructions '2/23' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-U Yellow & Blue'. Fibre/NBR materials, available in yellow or blue colours, manufactured by calendaring. Tesnit BA-U Blue is for use with water up to 85°C. Between September 2025 and February 2026, Tesnit BA-U Yellow was for use with water up to 23°C. Between March 2026 and September 2030, Tesnit BA-U Yellow is for use with water up to 85°C. Store and handle in accordance with 'STORING & HANDLING INSTRUCTIONS, dated November 12, 2025'. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'VPL500T/VPL500B VIP Seal Lubricant'. White coloured (opaque), water based lubricant. For use with water up to 23°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
'Tritan™ TX1501HF'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Tritan™ TX1001'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Tritan™HM1060'. Clear (translucent), injection moulded copolyester material. For use with water up to 85°C.
'Tritan™ TX2001'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Radius Systems PE100 Black Spigot Fittings'. Black coloured, injection moulded PE100 spigot fittings. For use with water up to 23°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
'B1-4773' Lip Seals and 'O' rings. Black coloured, EPDM components with shore hardness of 70. Compression moulded Lip Seals have an in-radius size of 2.7mm. Compression moulded ‘O’ rings have an in-radius size of 1.5mm. Injection moulded ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'EP0E7001P-WRC'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'E7581'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ECL/EP/50 & ECL/EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E7131'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'VEV1'. Black coloured, compression moulded FKM seal. Shore hardness 70 A. Tested in-radius size 4.45mm. For use with water up to 23°C.
'FKM 70 514404'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
72401, 72501, 73401, 73501, 74401, 74501, 75401, 75501, 76401, 76501, 77401, 77501, 78401, 78501, 79401 & 79501. Range of press moulded, solid silicone rubber materials which are blue or red coloured. Shore hardness between 20 & 90. Tested in-radius size 1.0mm. for use with water up to 85°C.
'Weld-On 719 Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '719-05-2024'. Cure for 8 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 795 Blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's data sheet '795-05-2024'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 705 ECO Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '705 ECO-09-2024'. Cure for 12 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hytrel® 4068FGDW'. Cream coloured, injection moulded, thermoplastic polyester elastomeric material. For use with water up to 23°C.
Range of deck mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Page 212 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
