‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings. For use with stainless steel tube. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2011045

Size:

15, 18, 22, 28, 35, 42, 54, 76, 88, 108, 114, 139, 168mm. ½”, ¾”, 1”, 1 ¼”, 1 ½”, 2” BSP (M or F). DN50 to DN150 Flanged.

Marking:

Numepress, logo & size on body

Installation Requirements:

R001

Expiry date:

30/11/2025

Model:

F1 Coupling from 15 to 168.3 F2 Slip Coupling from 15 to 168.3 F3 90Q Female-Female Elbow from 15 to 168.3 F4 90Q Male - Female Elbow from 15 to 168.3 F5 45Q Female-Female Elbow from 15 to 168.3 F6 45Q Female - Male Elbow from 15 to 168.3 F7 Female Angle Adapter from 15 1/2" to 54 2" F8 Male Angle Adapter from 15 1/2" to 54 2" F9 Female Elbow with Wallnut from 15 1/2" to 22 3/4" Fl0 90Q Elbow with Plane Ends from 15 to 54 F11 Valve connector with swivel in stainless Steel from 15 1/2" to 76.121/2" F12 Female tee threaded adaptor from 15 1/2" to 108 2" F14 Reducer from 18-15 to 168.3-139.7 F15 Reducing tee from 18-15 to 168.3-139.7 F16 Equal Tee from 15 to 168.3 F17 Female adaptor from 15 3/ 8" to 88.9 3" F18 M ale adaptor from 15 3/8" to 108 4" F19 Flanges adaptor from 15 DN15 to 108 DNlO0 F20 Pre-formed pipe bridge from 15 to 28 F21 Plug from 15 to 108 F22 Air tuve Pipe Bridge from 15 to 28 F23 Pipe Bridge from 15 to 28 F24 3 Pieces adaptor from 15 to 60.3 F25 Female -Female pipe bridge from 15 to 28 F26 Female connector from 15 1/2" to 54 2" F27 Male connector from 15 1/2" to 54 2" F28 Press flanged adaptor from 54 DN50 to 168.3 DN150 F30 Cross or reduced cross from 15-15-15-15 to 168.3-168.3-168.3-168 .3 F33 45Q Male angle adaptor from 15 1/ 2" to 28 1" F34 90Q Female angle adaptor 15 3/ 8" to 35 1 1/ 4" F35 90Q Female angle adaptor with swivel nut from 15 1/2" to 54 2" F36 Male Tee threaded adaptor from 15 3/8" to 35 11/4" F37 Male threaded cross from 15 1/2" to 108-4" F38 Female threaded cross from 15 1/ 2" to 108 4" F39 90Q Male angle adaptor from 15 3/8" to 54 2" F41 Male union connector gas from 15 1/ 2" to 54 2" F42 Female Union connector gas from 15 1/2" to 54 2" F43 Grooved Transition from 3/4" to 2" F44 Van Stone flange from 1/2" to 2" F45 Union Gas Female threaded from 15 3/4" to 54 2" F46 Straight union with press fitting on both ends from 15 to 54 F47 Half coupling from 15 to 168.3 F48 30Q Female-Female elbow from 15 to 108 F49 30Q Elbow with plain ends from 15 to 54 F50 15Q Female-female elbow from 15 to 108 F51 60Q Female-female elbow from 15 to 108 F52 Flanges adaptor PN6 from 15 DN15 to 108 DN100 F53 Pipe penetration from 15 to 108 F54 Male plug from 16 to 168.3 F55 Weld Adaptor from 15 to 60.3 F56 75Q Female -Female elbow from 15 to 108 F57 l0Q Female-Female elbow from 15 to 108 F58 60Q Elbow with plain ends from 15 to 54 F59 lSQ Elbow with plain ends from 15 to 54 F60 Slip coupling with female thread from DN15 1/ 2" to DN54 F61 Transition for grooved coupling from DN28x33.7 to DN108x 11 4.3 F63 7SQ Elbow with plain ends from 15 to 54 F64 15Q Male -female elbow from 15 to 108 F65 Male-Female pipe penetration from 15 to 108 F66 30Q Male-female elbow from 15 to 108 F72 45Q Elbow with plain ends from 15 to 54 Pipe 15 x 0.6 mm Material 1.4401/1.4404 Pipe 18 x 0.7 mm Material 1.4401/1.4404 Pipe 22 x 0.7 mm Material 1.4401/1.4404 Pipe 28 x 0.8 mm Material 1.4401/1.4404 Pipe 35 x 1 mm Material 1.4401/1.4404 Pipe 42 x 1.1 mm Material 1.4401/1.4404 Pipe 54 x 1.2 mm Material 1.4401/1.4404 Pipe 76.1 x 1.5 mm Material 1.4 401/ 1.4404 Pipe 15 x 1 mm Material 1.4401/1.4404 Pipe 18 x 1 mm Material 1.4401/1.4404 Pipe 22 x 1.2 mm Material 1.4401/1.4404 Pipe 28 x 1.2 mm Material 1.4401/1.4404 Pipe 35 x 1.5 mm Material 1.4401/1.4404 Pipe 42 x 1.5 mm Material 1.4401/1.4404 Pipe 54 x 1.5 mm Material 1.4401/1.4404 Pipe 76.1 x 2 mm Material 1.4401/1.4404 Pipe 88.9 x 2 mm Material 1.4401/1.4404 Pipe 114.3 x 2 mm Material 1.4401/1.4404 Pipe 139.7 x 2 mm Material 1.4401/1.4404 Pipe 139.7 x 2.6 mm Material 1.4401/1.4404 Pipe 168.3 x 2 mm Material 1.4401/1.4404 Pipe 168.3 x 2.6 mm Material 1.4401/1.4404 Pipe 15 x 0.6 mm Material 1.4301/1.4307 Pipe 18 x 0.7 mm Material 1.4301/1.4307 Pipe 22 x 0.7 mm Material 1.4301/1.4307 Pipe 28 x 0.8 mm Material 1.4301/1.4307 Pipe 35 x 1 mm Material 1.4301/1.4307 Pipe 42 x 1.1 mm Material 1.4301/1.4307 Pipe 54 x 1 .2 mm rv,Material 1.4301/1.4307 Pipe 76.1 x 1.5 mm Material 1.4301/1.4307 Pipe 15 x 1 mm Material 1.4301/1.4307 Pipe 18 x 1 mm Material 1.4301/1.4307 Pipe 22 x 1. 2 mm Material 1.4301/1.4307 Pipe 28 x 1.2 mm Material 1.4301/1.4307 Pipe 35 x 1.5 mm Material 1.4301/1.4307 Pipe 42 x 1.5 mm Material 1.4301/1.4307 Pipe 54 x 1.5 mm Material 1.4301/1.4307 Pipe 76.1 x 2 mm Material 1.4301/1.4307 Pipe 88.9 x 2 mm Material 1.4301/1.4307 Pipe 108 x 2 mm Material 1.4301/1.4307 Pipe 114.3 x 2 mm Material 1.4301/1.4307 Pipe 139.7 x 2 mm Material 1.4301/1.4307 Pipe 139.7 x 2.6 mm Material 1.4301/1 .4307 Pipe 168.3 x 2 mm Material 1.4301/1.4307 Pipe 168.3 x 2.6 mm Material 1.4301/1.4307

Product Images

Approval Holder:

ISOTUBI SL

Company Name

ISOTUBI SL

Address

Mecànica 6 Castellbisbal

Postcode

08750

Country

Spain

General Email

xavi.armengou@isotubi.com

View All Listings by this Company

‘Epsilon Series’ polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2010385

Note:

The liners supplied with each fitting must be used to maintain the validity of this approval. R008 applies to the connecting blue pipework when used above ground.

Size:

See model

Marking:

Fittings: Elysee, DVGW, EU, size and PN on the compression nut. Size and date of manufacture (clock format) on body. Pipe: Elysee, EN12201, size, PN and production date code (CDDMMY, where C = decade, and is replaced with 6 to indicate 2020).

Installation Requirements:

R001 R008

Expiry date:

31/10/2025

Model:

ELYSEE COMRESSION FITTINGS: Male Adaptor 330: 330002001: Ø 20 x ½". 330002002: Ø 20 x ¾". 330002003: Ø 20 x 1". 330002501: Ø 25 x ½". 330002502: Ø 25 x ¾". 330002503: Ø 25 x 1". 330003201: Ø 32 x ½". 330003202: Ø 32 x ¾". 330003203: Ø 32 x 1". 330003204: Ø 32 x 1¼". 330003205: Ø 32 x 1½". Female Adaptor 330A: 330A02001: Ø 20 x ½". 330A02002: Ø 20 x ¾". 330A02010: Ø 20 x ⅜". 330A02501: Ø 25 x ½". 330A02502: Ø 25 x ¾". 330A02503: Ø 25 x 1". 330A03201: Ø 32 x ½". 330A03202: Ø 32 x ¾". 330A03203: Ø 32 x 1". 330A03204: Ø 32 x 1¼". 330A03205: Ø 32 x 1½". End Plug 330B: 330B00020: Ø 20. 330B00025: Ø 25. 330B00032: Ø 32. Coupling 331: 331020020: Ø 20 x 20. 331025025: Ø 25 x 25. 331032032: Ø 32 x 32. Reducing Coupling 331A: 331A02520: Ø 25 x 20. 331A03220: Ø 32 x 20. 331A03225: Ø 32 x 25. Elbow 332: 332020020: Ø 20 x 20. 332025025: Ø 25 x 25. 332032032: Ø 32 x 32. Male Elbow 332A: 332A02001: Ø 20 x ½". 332A02002: Ø 20 x ¾". 332A02501: Ø 25 x ½". 332A02502: Ø 25 x ¾". 332A02503: Ø 25 x 1". 332A03202: Ø 32 x ¾". 332A03203: Ø 32 x 1". Female Elbow 332B: 332B02001: Ø 20 x ½". 332B02002: Ø 20 x ¾". 332B02501: Ø 25 x ½". 332B02502: Ø 25 x ¾". 332B02503: Ø 25 x 1". 332B03202: Ø 32 x ¾". 332B03203: Ø 32 x 1". Female Tee 333: 333002001: Ø 20 x ½" x 20. 333002002: Ø 20 x ¾" x 20. 333002501: Ø 25 x ½" x 25. 333002502: Ø 25 x ¾" x 25. 333002503: Ø 25 x 1" x 25. 333003202: Ø 32 x ¾" x 32. 333003203: Ø 32 x 1" x 32. Male Tee 333A: 333A02001: Ø 20 x ½" x 20. 333A02002: Ø 20 x ¾" x 20. 333A02003: Ø 20 x 1" x 20. 333A02501: Ø 25 x ½" x 25. 333A02502: Ø 25 x ¾" x 25. 333A02503: Ø 25 x 1" x 25. 333A03201: Ø 32 x ½" x 32. 333A03202: Ø 32 x ¾" x 32. 333A03203: Ø 32 x 1" x 32. Tee 334: 334020020: Ø 20 x 20 x 20. 334025025: Ø 25 x 25 x 25. 334032032: Ø 32 x 32 x 32. Reducing Tee 334A: 334A02520: Ø 25 x 20 x 25. 334A03225: Ø 32 x 25 x 32. Wall Female Elbow 332D: 332D02001: Ø 20 x ½". 332D02502: Ø 25 x ¾". Elbow Female For POP-UP 332C: 332C02501: Ø 25 x ½" x 25. 332C03201: Ø 32 x ½" x 32. 332C03202: Ø 32 x ¾" x 32. Universal Adaptor 321C: 321C02522: Ø 25 x 22. 321C03222: Ø 32 x 22. Repair Coupling 331B: 331B00025: Ø 25 x 25. 331B00032: Ø 32 x 32. ELYSEE PE80 BLUE PIPES: 21125020***: 20mmX2.3mm, SDR9, SF1.25, PN12.5. 21125025***: 25mmX2.3mm, SDR11, SF1.25, PN12.5. 21125032***: 32mmX3.0mm, SDR11, SF1.25, PN12.5. Where *** = length of the pipe coil, (025 = 25m, 050 = 50m, 100 = 100m).

Approval Holder:

Elysee Irrigation Ltd.

Company Name

Elysee Irrigation Ltd.

Address

5, Pentadaktylou St. 2643 Ergates Industrial Area, Nicosia

Country

Cyprus

Phone

+357 22 455 000

View All Listings by this Company

Manufacturer:

Elysee Irrigation Ltd.

Company Name

Elysee Irrigation Ltd.

Address

5, Pentadaktylou St. 2643 Ergates Industrial Area, Nicosia

Country

Cyprus

Phone

+357 22 455 000

View All Listings by this Company

Range of press fittings with a stainless steel body and EPDM ‘O’ rings for use with stainless steel 316L pipe manufactured to EN10312. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2101334

Size:

see model

Marking:

Dunshan Press and size on body.

Installation Requirements:

R001

Expiry date:

31/01/2026

Model:

DS2001‐15 Equal coupling 15mm DS2001‐18 Equal coupling 18mm DS2001‐22 Equal coupling 22mm DS2001‐28 Equal coupling 28mm DS2001‐35 Equal coupling 35mm DS2001‐42 Equal coupling 42mm DS2001‐54 Equal coupling 54mm DS2002‐15 Adjustable coupling 15mm DS2002‐18 Adjustable coupling 18mm DS2002‐22 Adjustable coupling 22mm DS2002‐28 Adjustable coupling 28mm DS2002‐35 Adjustable coupling 35mm DS2002‐42 Adjustable coupling 42mm DS2002‐54 Adjustable coupling 54mm DS2003‐15 90° equal elbow 15mm DS2003‐18 90° equal elbow 18mm DS2003‐22 90° equal elbow 22mm DS2003‐28 90° equal elbow 28mm DS2003‐35 90° equal elbow 35mm DS2003‐42 90° equal elbow 42mm DS2003‐54 90° equal elbow 54mm DS2004‐15 90° plain elbow‐B 15mm DS2004‐18 90° plain elbow‐B 18mm DS2004‐22 90° plain elbow‐B 22mm DS2004‐28 90° plain elbow‐B 28mm DS2004‐35 90° plain elbow‐B 35mm DS2004‐42 90° plain elbow‐B 42mm DS2004‐54 90° plain elbow‐B 54mm DS2005‐15 45° equal elbow 15mm DS2005‐18 45° equal elbow 18mm DS2005‐22 45° equal elbow 22mm DS2005‐28 45° equal elbow 28mm DS2005‐35 45° equal elbow 35mm DS2005‐42 45° equal elbow 42mm DS2005‐54 45° equal elbow 54mm DS2006‐15 45° plain elbow‐B 15mm DS2006‐18 45° plain elbow‐B 18mm DS2006‐22 45° plain elbow‐B 22mm DS2006‐28 45° plain elbow‐B 28mm DS2006‐35 45° plain elbow‐B 35mm DS2006‐42 45° plain elbow‐B 42mm DS2006‐54 45° plain elbow‐B 54mm DS2007‐15 Equal tee 15mm DS2007‐18 Equal tee 18mm DS2007‐22 Equal tee 22mm DS2007‐28 Equal tee 28mm DS2007‐35 Equal tee 35mm DS2007‐42 Equal tee 42mm DS2007‐54 Equal tee 54mm DS2008‐18*15 Reducing tee 18mm×15mm DS2008‐22*15 Reducing tee 22mm×15mm DS2008‐22*18 Reducing tee 22mm×18mm DS2008‐28*15 Reducing tee 28mm×15mm DS2008‐28*18 Reducing tee 28mm×18mm DS2008‐28*22 Reducing tee 28mm×22mm DS2008‐35*15 Reducing tee 35mm×15mm DS2008‐35*18 Reducing tee 35mm×18mm DS2008‐35*22 Reducing tee 35mm×22mm DS2008‐35*28 Reducing tee 35mm×28mm DS2008‐42*15 Reducing tee 42mm×15mm DS2008‐42*18 Reducing tee 42mm×18mm DS2008‐42*22 Reducing tee 42mm×22mm DS2008‐42*28 Reducing tee 42mm×28mm DS2008‐42*35 Reducing tee 42mm×35mm DS2008‐54*15 Reducing tee 54mm×15mm DS2008‐54*18 Reducing tee 54mm×18mm DS2008‐54*22 Reducing tee 54mm×22mm DS2008‐54*28 Reducing tee 54mm×28mm DS2008‐54*35 Reducing tee 54mm×35mm DS2008‐54*42 Reducing tee 54mm×42mm DS2009‐15*Rp1/2 Female coupling 15mm×Rp1/2’’ DS2009‐22*Rp3/4 Female coupling 22mm×Rp3/4” DS2009‐28*Rp1 Female coupling 28mm×Rp1” DS2009‐35*Rp1 1/4 Female coupling 35mm×Rp1‐“1/4” DS2009‐42*Rp1 1/2 Female coupling 42mm×Rp1‐1/2” DS2009‐54*Rp2 Female coupling 54mm×Rp2” DS2010‐15*G1/2 Rotatable coupling 15mm×G1/2” DS2010‐18*G1/2 Rotatable coupling 18mm×G1/2” DS2010‐22*G3/4 Rotatable coupling 22mm×G3/4” DS2010‐28*G1 Rotatable coupling 28mm×G1” DS2010‐35*G1 1/4 Rotatable coupling 35mm×G1‐1/4” DS2010‐42*G1 1/2 Rotatable coupling 42mm×G1‐1/2” DS2010‐54*G2 Rotatable coupling 54mm×G2” DS2011‐15*R1/2 Male coupling 15mm×R1/2” DS2011‐18*R1/2 Male coupling 18mm×R1/2” DS2011‐22*R3/4 Male coupling 22mm×R3/4” DS2011‐28*R1 Male coupling 28mm×R1” DS2011‐35*R1 1/4 Male coupling 35mm×R1‐1/4” DS2011‐42*R1 1/2 Male coupling 42mm×R1‐1/2” DS2011‐54*R2 Male coupling 54mm×R2” DS2012‐15*Rp1/2 Female elbow 15mm×Rp1/2” DS2012‐18*Rp1/2 Female elbow 18mm×Rp1/2” DS2012‐22*Rp3/4 Female elbow 22mm×Rp3/4” DS2012‐28*Rp1 Female elbow 28mm×Rp1” DS2012‐35*Rp1 1/4 Female elbow 35mm×Rp1‐1/4” DS2012‐42*Rp1 1/2 Female elbow 42mm×Rp1‐1/2” DS2012‐54*Rp2 Female elbow 54mm×Rp2” DS2013‐15*R1/2 Male elbow 15mm×R1/2” DS2013‐18*R1/2 Male elbow 18mm×R1/2” DS2013‐22*R1/2 Male elbow 22mm×R1/2” DS2013‐22*R3/4 Male elbow 22mm×R3/4” DS2013‐28*R1 Male elbow 28mm×R1” DS2013‐35*R1 1/4 Male elbow 35mm×R1‐1/4” DS2013‐42*R1 1/2 Male elbow 42mm×R1‐1/2” DS2013‐54*R2 Male elbow 54mm×R2” DS2014‐15*Rp1/2 Female tee 15mm×Rp1/2” DS2014‐18*Rp1/2 Female tee 18mm×Rp1/2” DS2014‐22*Rp3/4 Female tee 22mm×Rp3/4” DS2014‐28*Rp1/2 Female tee 28mm×Rp1/2 DS2014‐28*Rp1 Female tee 28mm×Rp1” DS2014‐35*Rp1 1/4 Female tee 35mm×Rp1‐1/4” DS2014‐42*Rp1 1/2 Female tee 42mm×Rp1‐1/2” DS2014‐54*Rp2 Female tee 54mm×Rp2” DS2015‐15*R1/2 Male tee 15mm×R1/2” DS2015‐18*R1/2 Male tee 18mm×R1/2” DS2015‐22*R3/4 Male tee 22mm×R3/4” DS2015‐28*R1/2 Male tee 28 mm×R1/2’’ DS2015‐28*R1 Male tee 28mm×R1” DS2015‐35*R1 1/4 Male tee 35mm×R1‐1/4” DS2015‐42*R1 1/2 Male tee 42mm×R1‐1/2” DS2015‐54*R2 Male tee 54mm×R2” DS2016‐18*15 Reducer‐A 18mm×15mm DS2016‐22*15 Reducer‐A 22mm×15mm DS2016‐22*18 Reducer‐A 22mm×18mm DS2016‐28*15 Reducer‐A 28mm×15mm DS2016‐28*18 Reducer‐A 28mm×18mm DS2016‐28*22 Reducer‐A 28mm×22mm DS2016‐35*15 Reducer‐A 35mm×15mm DS2016‐35*18 Reducer‐A 35mm×18mm DS2016‐35*22 Reducer‐A 35mm×22mm DS2016‐35*28 Reducer‐A 35mm×28mm DS2016‐42*15 Reducer‐A 42mm×15mm DS2016‐42*18 Reducer‐A 42mm×18mm DS2016‐42*22 Reducer‐A 42mm×22mm DS2016‐42*28 Reducer‐A 42mm×28mm DS2016‐42*35 Reducer‐A 42mm×35mm DS2016‐54*42 Reducer‐A 54mm×42mm DS20107‐18*15 Reducer Coupling‐B 18mm×15mm DS20107‐22*15 Reducer Coupling‐B 22mm×15mm DS20107‐22*18 Reducer Coupling‐B 22mm×18mm DS20107‐28*15 Reducer Coupling‐B 28mm×15mm DS20107‐28*18 Reducer Coupling‐B 28mm×18mm DS20107‐28*22 Reducer Coupling‐B 28mm×22mm DS20107‐35*15 Reducer Coupling‐B 35mm×15mm DS20107‐35*18 Reducer Coupling‐B 35mm×18mm DS20107‐35*22 Reducer Coupling‐B 35mm×22mm DS20107‐35*28 Reducer Coupling‐B 35mm×28mm DS20107‐42*15 Reducer Coupling‐B 42mm×15mm DS20107‐42*18 Reducer Coupling‐B 42mm×18mm DS20107‐42*22 Reducer Coupling‐B 42mm×22mm DS20107‐42*28 Reducer Coupling‐B 42mm×28mm DS20107‐42*35 Reducer Coupling‐B 42mm×35mm DS20107‐54*15 Reducer Coupling‐B 54mm×15mm DS20107‐54*18 Reducer Coupling‐B 54mm×18mm DS20107‐54*22 Reducer Coupling‐B 54mm×22mm DS20107‐54*28 Reducer Coupling‐B 54mm×28mm DS20107‐54*35 Reducer Coupling‐B 54mm×35mm DS20107‐54*42 Reducer Coupling‐B 54mm×42mm

Product Images

Approval Holder:

Wenzhou Dunshan EPT Co.,Ltd.

Company Name

Wenzhou Dunshan EPT Co.,Ltd.

Address

Building B, No. 500, Lingde Road, Kunpeng Street, Oujiangkou Industrial Cluster, Wenzhou City, Zhejiang Province

Country

China

View All Listings by this Company

Manufacturer:

Wenzhou Dunshan EPT Co.,Ltd.

Company Name

Wenzhou Dunshan EPT Co.,Ltd.

Address

Building B, No. 500, Lingde Road, Kunpeng Street, Oujiangkou Industrial Cluster, Wenzhou City, Zhejiang Province

Country

China

View All Listings by this Company

Range of brass and copper fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 18.6 bar. Maximum operating temperature 100°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2011341

Size:

See model

Marking:

Endex Logo or Endbraze on body.

Installation Requirements:

R001

Expiry date:

30/11/2025

Model:

N1 Straight Coupling: 88030 - 67mm 89600 - 76mm 89601 - 108mm 89697 - 133mm 89698 - 159mm B12 Elbow: 88456 – 67mm 89619 – 76mm N61 Stop End: 89090 – 67mm 89694 – 76mm 89695 – 108mm N69P Straight Male Union Connector: 89253 – 67mm N1IM Met x Imp Adaptor Coupling: 89617 – 76mm x 3” 89618 – 108mm x 4” N18 Slow Bend: 89639 – 67mm 89640 – 76mm 89741 – 108mm 89709 – 133mm 89710 – 159mm N1FMGI Bi-Metal Flange: 88028 – 42mm (4 holes) 88029 – 54mm (4 holes) 88114 – 67mm (4 holes) 89603 – 76mm (8 holes) 89604 – 108mm (8 holes) 89602 – 133mm (8 holes) 89719 – 159mm (8 holes) N3 Straight Male Connector: 88200 – 67mm x 2 ½” 89615 – 76mm x 3” 89616 – 108mm x 4” N21 Obtuse Elbow: 88653 – 67mm 89645 – 76mm 89646 – 108mm 89711 – 133mm 89712 – 159mm N1FMB Gunmetal Flange: 89605 – 76mm (8 holes) N6 Reducer: 88310 – 67mm x 28mm 88311 – 67mm x 35mm 88312 – 67mm x 42mm 88313 – 67mm x 54mm 89624 – 76mm x 35mm 89625 – 76mm x 42mm 89626 – 76mm x 54mm 89627 – 76mm x 67mm 89630 – 108mm x 42mm 89631 – 108mm x 54mm 89632 – 108mm x 67mm 89633 – 108mm x 76mm 89699 – 133mm x 42mm 89700 – 133mm x 54mm 89701 – 133mm x 67mm 89702 – 133mm x 76mm 89703 – 133mm x 108mm 89704 – 159mm x 54mm 89705 – 159mm x 67mm 89706 – 159mm x 76mm 89707 – 159mm x 108mm 89708 – 159mm x 133mm N24 Equal Tee: 88719 – 67mm 89648 – 76mm 89649 – 108mm 89713 – 133mm 89714 – 159mm N25 Tee Reduced Branch: 88807 – 67mm x 67mm x 28mm 89055 – 67mm x 67mm x 35mm 89056 – 67mm x 67mm x 42mm 89057 – 67mm x 67mm x 54mm 89058 – 76mm x 76mm x 28mm 89000 – 76mm x 76mm x 35mm 89654 – 76mm x 76mm x 42mm 89001 – 76mm x 76mm x 54mm 89059 – 108mm x 108mm x 35mm 89660 – 108mm x 108mm x 54mm 89002 – 108mm x 108mm x 76mm 89715 – 133mm x 133mm x 54mm 89716 – 133mm x 133mm x 108mm 89717 – 159mm x 159mm x 54mm 89718 – 159mm x 159mm x133mm

Product Images

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Dual flush, WC outlet valves. Model A2706 is operated via a push button assembly for either full or reduced flush. Models A2415L & A2415M are not supplied with a operating button. Maximum operating temperature. Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2011016

Size:

2” BSP (M)

Marking:

R&T, model name, WRAS logo and date of manufacture (YY/MM) on body.

Installation Requirements:

R001

Expiry date:

30/11/2025

Model:

A2415L, A2415M & A2706

Product Images

Approval Holder:

Xiamen R&T Plumbing Technology Co.,Ltd

Company Name

Xiamen R&T Plumbing Technology Co.,Ltd

Address

No.18, Houxiang Road Haicang District Xiamen

Postcode

361022

Country

China

Phone

86-0592-3959422

General Email

rt025@rtplumbing.com

View All Listings by this Company

Manufacturer:

Xiamen R&T Plumbing Technology Co.,Ltd

Company Name

Xiamen R&T Plumbing Technology Co.,Ltd

Address

No.18, Houxiang Road Haicang District Xiamen

Postcode

361022

Country

China

Phone

86-0592-3959422

General Email

rt025@rtplumbing.com

View All Listings by this Company

Range of waste water heat recovery systems incorporating a twin wall copper coil (iZi models) or stainless steel (PiPe models). Maximum working pressure 10.0 bar. Cold water use only.

Section:

1350 Heat Exchangers

Size:

½” BSP (M) (iZi 30 & 40) or ¾” BSP (F) (PiPe 65 & 70)

Marking:

Zypho, Model, WRAS and technical info on adhesive label located on plastic casing.

Installation Requirements:

R001

Expiry date:

31/12/2025

Model:

ZYPHO iZi 30, ZYPHO iZi 40, ZYPHO PiPe 65, ZYPHO PiPe 70

Product Images

Approval Holder:

Zypho, SA

Company Name

Zypho, SA

Country

Portugal

Phone

+351 210 991 351

General Email

b2b@zypho.pt

View All Listings by this Company

Manufacturer:

Zypho, SA

Company Name

Zypho, SA

Country

Portugal

Phone

+351 210 991 351

General Email

b2b@zypho.pt

View All Listings by this Company

Range of indirect heat interface units with copper brazed stainless-steel heat exchangers, providing heating and instantaneous hot water. The products incorporate an expansion vessel on the cold-water supply to the plate heat exchanger and a safety relief valve on the space heating circuit set @ 3.0 bar. The domestic hot water and space heating circuit are both fitted with drain valves incorporating cover caps. Maximum working pressures: Domestic hot water 10.0 bar. Space Heating 2.5 bar. District Heating 3.0 bar. Maximum operating temperature 85˚C.

Section:

1350 Heat Exchangers

WRAS Approval Number:

2011035

Note:

There are no pipework connections on this product to facilitate the filling of the space heating circuit. The installer must provide this separately.

Size:

Domestic hot water and District heating circuits: ¾” BSP (M) inlet/outlet. Space heating circuit: ¾” BSP captive nut inlet/outlet.

Marking:

YGHP on front cover. YGHP, model number, company address and technical info on adhesive label on side of body.

Installation Requirements:

R001 R140 R360 R511

Expiry date:

30/11/2025

Proviso:

Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999.

Model:

YGINDRADSTD33/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 33kW / HTG 10kW. YGINDRADSTD40/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 40kW / HTG 10kW. YGINDRADSTD50/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 50kW / HTG 10kW. YGINDRADSTD60/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 60kW / HTG 10kW. YGINDRADSTD75/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 75kW / HTG 10kW. YGINDRADSTD90/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 90kW / HTG 10kW. YGINDRADSTD120/10.1 - YGHP INDIRECT STANDARD HIU (RADIATORS) - DHW 120kW / HTG 10kW. Models added March 2021: YGINDUFHSTD33/10.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 33kW / HTG 10kW YGINDUFHSTD40/10.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 40kW / HTG 10kW YGINDUFHSTD50/10.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 50kW / HTG 10kW YGINDUFHSTD60/10.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 60kW / HTG 10kW YGINDUFHSTD75/15.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 75kW / HTG 15kW YGINDUFHSTD90/15.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 90kW / HTG 15kW YGINDUFHSTD120/30.1 - YGHP INDIRECT STANDARD HIU (UFH) - DHW 120kW / HTG 30kW

Product Images

Approval Holder:

YGHP Ltd

Company Name

YGHP Ltd

View All Listings by this Company

Range of stainless-steel heat exchangers. Maximum working pressure of primary Circuit 3.0 bar. Maximum working pressure of secondary Circuit 10.0 bar. Maximum operating temperature 80˚C

Section:

1350 Heat Exchangers

Size:

Primary Circuit ¾” captive nut x ¾” BSP (M) Sanitary Circuit 21mm (OD) Spigot Fitting x ½” BSP (M)

Marking:

Condevo SpA, serial number and date of manufacture (DD/MM/YY) on adhesive label on body.

Installation Requirements:

R001

Expiry date:

31/01/2026

Model:

Type E 12439 PP11CE6V02, PP21CE6V02 & PP33CE6V02. Type E 12440 PP10CE6H02, PP22CE6H02 & PP34CE6H02.

Product Images

Approval Holder:

Condevo SpA

Company Name

Condevo SpA

Address

Via Luna, Z.A. 26866 Marudo (LO) Italy

View All Listings by this Company

Manufacturer:

Condevo SpA

Company Name

Condevo SpA

Address

Via Luna, Z.A. 26866 Marudo (LO) Italy

View All Listings by this Company

Electronically controlled heat interface units (HIU) with twin stainless-steel plate heat exchangers providing space heating and instantaneous hot water. The cold inlet supply to the plate heat exchanger incorporates an isolation valve and a water hammer arrestor. The space heating circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product is supplied with a filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (suitable for backflow protection against fluid category 3) which incorporates an isolation valve. The cold mains inlet and the domestic hot water outlet each incorporate a brass bodied spherical valve with a butterfly handle. Maximum working pressures and operating temperatures: Primary: 16.0 bar and 90˚C. Domestic hot water (DHW): 10 bar and 65˚C. Secondary (space heating): 2.5 bar and 85˚C.

Section:

1350 Heat Exchangers

Size:

¾” BSP (M)

Marking:

Inta logo, address, serial number, technical & pressure information on label inside case.

Installation Requirements:

R001

Expiry date:

31/12/2025

Proviso:

Supplied with a temporary filling loop. The filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999.

Model:

HIPER2TPSZ80 HIPER2SPSW80 HIPER2SPSW80IS HIPER2SPSW80ZE

Product Images

Approval Holder:

Intatec Limited

Company Name

Intatec Limited

Address

Airfield Industrial Estate Hixon Staffordshire

Postcode

ST18 0PF

Country

United Kingdom

Phone

01889272180

General Email

ryan.tilsley@intatec.co.uk

View All Listings by this Company

Range of RINNAI continuous flow water heaters with stainless steel plate heat exchangers providing heating and instantaneous hot water .The hot water is generated via a plate heat exchanger. Also supplied is a drain valve and a flow sensing device. Maximum working pressure - 10 bar Maximum working pressure - 85˚C

Section:

1350 Heat Exchangers

Size:

¾” Male inlet and outlet

Marking:

RINNAI on body and data badge including date of manufacture (YY/MM)

Installation Requirements:

R001

Expiry date:

31/10/2025

Model:

REU-N3237FFC-E – N1600i (57.9kW / 29Kg) REU-N3237WC-E – N1600e (57.9kW / 29Kg) REU-N2635FFC-E – N1300i (47kW / 28Kg) REU-N2635WC-E – N1300e (47kW / 28Kg)

Product Images

Approval Holder:

Rinnai UK Ltd

Company Name

Rinnai UK Ltd

Address

9 Christleton Court Manor Park Runcom

Postcode

WA7 18T

Phone

01928 531 870

General Email

info@rinnaiuk.com

View All Listings by this Company

Manufacturer:

Rinnai UK Ltd

Company Name

Rinnai UK Ltd

Address

9 Christleton Court Manor Park Runcom

Postcode

WA7 18T

Phone

01928 531 870

General Email

info@rinnaiuk.com

View All Listings by this Company

Gas fired water heaters incorporating a heat exchanger and flow sensor. The inlet incorporates a plastic strainer. The products are supplied with isolation valves for installation on the cold inlet and hot outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C

Section:

1400 Heaters

Section Subtitle:

Gas fired, closed outlet. Heat retained in water heaters may cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to prevent excess pressure within the system.

WRAS Approval Number:

2101041

Size:

15mm Compression

Marking:

ECA on front of body. ECA. Model & technical information on adhesive label on side of body.

Installation Requirements:

R001 R140

Expiry date:

31/01/2026

Model:

8116180100 – Phoenix PH 11LT Water Heater.

Product Images

Approval Holder:

Emas Makina Sanayi A.S.

Company Name

Emas Makina Sanayi A.S.

Address

Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa

Postcode

45030

Country

Turkey

General Email

egecakmakci@emas.com.tr

View All Listings by this Company

Manufacturer:

Emas Makina Sanayi A.S.

Company Name

Emas Makina Sanayi A.S.

Address

Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa

Postcode

45030

Country

Turkey

General Email

egecakmakci@emas.com.tr

View All Listings by this Company

Range of wall mounted combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, incorporating a pressure relief valve set at 3.0 bar and expansion vessel on the primary circuit. The inlet of the replenishing valve between the primary and secondary circuits incorporate a plastic strainer. Maximum working pressure 2.5 bar (primary) and 6.0 bar (secondary). Maximum operating temperature 85˚C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2012051

Note:

Please note that the inlet pipework connects to the flow sensor, no fittings or valves prior to this are supplied. Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with Schedule 2 paragraph 7 of the Water Supply (Water Fittings) Regulations 1999.

Size:

½” BSP (M) inlet and outlet Secondary Circuit. ½” BSP (M) replenishing valve. ¾” BSP(M) inlet and outlet primary circuit.

Marking:

Strom on front of body. Model and technical info on adhesive label on side of body.

Installation Requirements:

R001 R140 R360

Expiry date:

31/12/2025

Model:

Strom E range comprising of models: SBSP7C, SBSP11C & SBSP15C. SBTP18C, SBTP21C & SBTP24C. The number in model indicates kW rating.

Approval Holder:

STROM LTD

Company Name

STROM LTD

View All Listings by this Company

LCB700 range of internal and external oil-fired condensing combination boilers providing domestic hot water and pressurised central heating via a plate heat exchanger. The products are supplied with a temporary filling loop which incorporates a combined isolation valve and double check valve assembly (suitable for backflow protection against Fluid Category 3), stainless steel braided EPDM lined flexible hose assembly and an isolation valve. The primary (space heating) circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). Operating parameters: Primary (space heating) circuit: Maximum working pressure 2.5 Bar. Maximum operating temperature 105°C. Secondary (DHW) circuit: Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2101042

Size:

Primary (space heating) circuit: 22mm pushfit. Secondary (DHW) circuit: 15mm pushfit.

Marking:

Navien, model and technical information on adhesive label on rear of front cover.

Installation Requirements:

R001 R140 R360 R430

Expiry date:

31/01/2026

Model:

Internal: LCB700-21LC. LCB700-28LC. LCB700-36LC. External: LCB700-21LCX. LCB700-28LCX. LCB700-36LCX

Product Images

Approval Holder:

KD Navien Co Ltd

Company Name

KD Navien Co Ltd

Address

4F Koami Bldg, 22 Gukhoe daero, 76-gil, Yeongdeungpo-gu, Seoul, 07238 Korea

Phone

+82 2 3489 2200

General Email

www.navien.com

View All Listings by this Company

Range of heat interface units (HIU) with either twin or single stainless steel copper brazed plate heat exchangers (depending on model) providing heating and hot water (twin unit) hot water only, or heating only. The hot water is generated via a plate heat exchanger. The primary (space heating) circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product incorporates a CAb backflow prevention device (suitable for backflow protection against Fluid Category 3) for filling the heating circuit. The inlet and outlet of all circuits incorporate a lever operated spherical valve. Maximum working pressures and operating temperatures: Primary (district heating): 10.0 bar and 85˚C. Domestic hot water (DHW): 10.0 bar and 60˚C. Secondary (space heating): 2.5 bar and 80˚C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2011358

Size:

22mm solder fitting

Marking:

Albion water management, model and other tech info on data label on the side panel.

Installation Requirements:

R001 R140

Expiry date:

30/11/2025

Model:

[Twin Unit]: Standard Twin Plate – heating with 24 plates and hot water with either 14 or 40 plates. Heating connection to cold water by filling loop. Products: TH000240 MTA TWIN 24-40 TH000214 MTA TWIN 24-14 TH001240 MTA TWIN 24-40 HM TH001214 MTA TWIN 24-14 HM [Hot Water Only]: Hot water with either 14 or 40 plates, connection direct to cold water. Products: TH000414 MTA HOT WATER ONLY 00-14 TH000440 MTA HOT WATER ONLY 00-40 TH001414 MTA HOT WATER ONLY 00-14 HM TH001440 MTA HOT WATER ONLY 00-40 HM [Heating Only]: Heating with 40 plates on domestic heating circuit only, connection to cold water via filling loop. Products: TH000340 MTA HEATING ONLY 40-00 TH001340 MTA HEATING ONLY 40-00 HM ‘HM’ stands for heat meter which is on the heating circuit

Product Images

Approval Holder:

Albion Water Management

Company Name

Albion Water Management

Address

30-31 Station Close, Potters Bar, Hertfordshire

Postcode

EN6 1TL

Phone

01707 607230

General Email

water@albiongroup.co.uk

View All Listings by this Company

Manufacturer:

Albion Water Management

Company Name

Albion Water Management

Address

30-31 Station Close, Potters Bar, Hertfordshire

Postcode

EN6 1TL

Phone

01707 607230

General Email

water@albiongroup.co.uk

View All Listings by this Company

Range of water meters with plastic or brass bodies. The inlets incorporate a plastic strainer. Maximum working pressure 16.0 bar. RTKD range has a maximum operating temperature of 50°C. RTKD-L range has a maximum operating temperature of 30°C.

Section:

1505 Water Meters

Size:

RTKD range: ¾” - 1½” BSP (M). RTKD-L range: ¾” - 1” BSP (M).

Marking:

Flow arrow on body. Zenner and date of manufacture (YYYY) on meter case.

Installation Requirements:

R001

Expiry date:

31/01/2026

Model:

RTKD range (brass body). RTKD-L range (plastic body).

Product Images

Approval Holder:

Zenner International Gmbh & Co. KG

Company Name

Zenner International Gmbh & Co. KG

Address

Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany

Country

Germany

View All Listings by this Company

Manufacturer:

Zenner Meters (Shanghai) Ltd.

Company Name

Zenner Meters (Shanghai) Ltd.

Address

No 15 Dongxing Road Songjiang Ind Zone Shanghai

Country

China

View All Listings by this Company

Ultrasonic water meter with a blue epoxy coated ductile iron body and EPDM ‘O’ rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Size:

DN50-200 Flanged

Marking:

NWM logo, size and model on dial face. Flow arrow and DN on valve body.

Installation Requirements:

R001

Expiry date:

31/01/2026

Model:

UL-BW

Product Images

Approval Holder:

Ningbo Water Meter (Group) Co., Ltd

Company Name

Ningbo Water Meter (Group) Co., Ltd

Address

No 355 Hongxing Road Jiangbei District Ningbo

Country

China

View All Listings by this Company

Manufacturer:

Ningbo Water Meter (Group) Co., Ltd

Company Name

Ningbo Water Meter (Group) Co., Ltd

Address

No 355 Hongxing Road Jiangbei District Ningbo

Country

China

View All Listings by this Company

Range of flow sensors with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C

Section:

1530 Miscellaneous Fittings

Size:

¾” BSP (M).

Marking:

Sika, part number and other information on adhesive label on cable. Flow arrow on body

Installation Requirements:

R001

Expiry date:

31/12/2025

Model:

Flow sensors type series VTY15 Models: VY1545abcdefgh ab:for body material (MA = Brass CW617N-DW, MK = Brass CW724R, K5 = without body, only the internal turbine system) cd: for sensor and signal output (HN = Hall sensor-NPN, 00 = without sensor) ef: for electrical cable connection (various - in combination can be 00…99 or AA…ZZ, examples 05 = 500mm, 12=1200mm, X1=80mm with Molex plug connector) gh: for process connection (A4 = G3/4 male thread, YY = without, only possible with ab = K5) VY1545abyyyyyzz ab: for body material (MA = Brass CW617N-DW, MK = Brass CW724R, K5 = without body, only the internal turbine system) yyyyy: for name of customer (5 digits, e.g. SCHMI, MUELL, …) zz: for consecutive number (2 digits, 01…99)

Product Images

Approval Holder:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Manufacturer:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Thermostatic element with copper shell, polyethylene tube and PTFE gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.

Section:

1530 Miscellaneous Fittings

WRAS Approval Number:

2012358

Note:

Please note that function and any claims of thermostatic control made by the manufacturer has not been assessed or verified as part of this approval.

Size:

2.54Ø

Marking:

SMLG (trademark of Shanghai Enjoy Bath Thermostatic Technology Co. Ltd.), batch number and model on copper shell.

Installation Requirements:

R001

Expiry date:

31/12/2025

Model:

LG075X

Product Images

Approval Holder:

Shanghai Enjoy Bath Thermostatic Technology Co. Ltd (SMLG)

Company Name

Shanghai Enjoy Bath Thermostatic Technology Co. Ltd (SMLG)

Address

F-202 Building 5 No.84 Jinwen Road Zhuqiao Town

Phone

+86-21-50321360

General Email

markyu@smlgood.com

View All Listings by this Company

Manufacturer:

Shanghai Enjoy Bath Thermostatic Technology Co. Ltd (SMLG)

Company Name

Shanghai Enjoy Bath Thermostatic Technology Co. Ltd (SMLG)

Address

F-202 Building 5 No.84 Jinwen Road Zhuqiao Town

Phone

+86-21-50321360

General Email

markyu@smlgood.com

View All Listings by this Company

Range of threaded fittings with either plain brass, nickel plated brass or chrome plated brass bodies. Maximum operating pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

1530 Miscellaneous Fittings

Size:

Plain brass bodies: 1/8" to 4" BSP. Nickel plated or chrome plated brass bodies: 1/8" - 1" BSP.

Marking:

‘E’ (brand of factor) & size on body.

Installation Requirements:

R001

Expiry date:

31/01/2026

Model:

IDC 25 range comprising of: Hexagon Nipple M x M Thread Bush Mi x Fi Flanged Blanking Nut RUNNING NIPPLE M x M SPACER NIPPLE M x M BARREL NIPPLE M x M Pipe Nipple M x M Thread Fi x Mi adaptor Thread Fi xFi Straight Reduce M x M adaptor Straight reduce M x F adaptor Straight reduce F x F adaptor Blanking cap Blanking Plug Elbow F x F adaptor Elbow reduce F x F adaptor Elbow M x M adaptor Elbow F x M adaptor Elbow F x F Wall plate TEE F x F x F TEE Reduce F x F x F Cross F x F x F x F Straight Pipe union M x F Straight Pipe union F x F Elbow Pipe union F x F

Product Images

Approval Holder:

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Company Name

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Address

3rd Floor, Unit 2, Building 2, Section A Zhaowei Science & Technology Park No. 14, Jiuxianqiao Road Chaoyang District Beijing

Postcode

100015

Country

China

Phone

008610 51659550 ext 312

General Email

Jerry.tang@idcgroup.com.cn

View All Listings by this Company

Manufacturer:

IDC Fluid Control Co., Ltd.

Company Name

IDC Fluid Control Co., Ltd.

Address

No.6, Shengyuan Road, Mechanical & Electrical Industrial Zone, Yuhuan City, Zhejiang, Taizhou City, Zhejiang Province, P. R.China

Country

China

General Email

View All Listings by this Company

Wallgate CWC Series 250 WC pan with direct acting flush valve and DFKIT03 air break (DC device). WC flushing mechanism has a solenoid valve controlling the flow, the valves are operated via an infrared sensor or a piezo control button, this mechanism is fitted with a DC pipe interrupter, the DFKIT03 is fitted with a flow regulator. Maximum working pressure 2.0 bar. Cold water use only.

Section:

1530 Miscellaneous Fittings

WRAS Approval Number:

2012036

Note:

No pressure flushing valve shall be installed in a house or in any building not being a house where a minimum flow rate of 1.2 litres per second cannot be achieved at the appliance.

Size:

Direct flush solenoid valve – 1” BSP Male inlet/outlet. DC Pipe Interrupter 1” BSP Female Inlet to 1 ½” BSP Male outlet.

Marking:

Wallgate, model and technical info on control box. Wallgate on WC Pan.

Installation Requirements:

R001 R390 R400

Expiry date:

31/12/2025

Model:

CWC-250. CWC-251. CWC-250-AST. CWC-251-AST. CWC-255. CWC-256. CWC-270-L. CWC-270-R. CWC-280. CWC-280-ST. CWC-281. CWC-281-ST.

Product Images

Approval Holder:

Wallgate Ltd.

Company Name

Wallgate Ltd.

Address

Crow Lane, Salisbury

Postcode

SP2 0HB

Country

United Kingdom

Phone

01722 702058

General Email

jmarshall@wallgate.com

View All Listings by this Company

Manufacturer:

Wallgate Ltd.

Company Name

Wallgate Ltd.

Address

Crow Lane, Salisbury

Postcode

SP2 0HB

Country

United Kingdom

Phone

01722 702058

General Email

jmarshall@wallgate.com

View All Listings by this Company