Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of screw down stop valves with brass or chrome plated brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of double regulating valves with DZR brass, products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line electrolytic scale reducer with chromium plated copper body for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
'KH369AC'. Dark grey coloured, compression moulded carbon/graphite ring. For use with water up to 85°C.
'NM 96 & NM 99 Ceramic Discs'. Off-white coloured, compression moulded ceramic discs. For use with water up to 85°C.
‘Rashmi Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/002', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Grivory HT1VA-4 FWA (Natural) & Grivory HT1VA-4 FWA black 9225'. Natural (appears beige-green coloured) & black, injection moulded nylon materials. For use with water up to 85°C.
'Grivory HT1VA-5 FWA black 9225'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'Badadur PBT9 GF10 WL Blau 1001'. Blue coloured, injection moulded PBT material. For use with water up to 23°C.
'SABIC® Vestolen A RELY 5924 R 10000 (Black)'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
Page 194 of 215
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
