‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TP1'. Factory applied, colourless solid lubricant. Apply as per manufacturer's instructions 'LDAP-005', issue 1, dated 11/11/2016. For use with water up to 85°C.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AF-300 B Pro'. Blue coloured, NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio
‘ZISIF GRP water tank panel'. For use with water up to 23°C. ‘ZISIF Premium GRP Water Tank Panel’ was added to the approval in February 2026 and is for use with water up to 55°C. Off-white coloured GRP panels manufactured by hot press moulding.
'Huili-GRP Water Tank Panel (HL002)'. Grey coloured (opaque), hot press moulded GRP panel. For use with water up to 23°C.
‘Neoperl Softpex® hose inliner’. Single layered, extruded, uncoloured (appears off-white, transparent) PEX-a tube. For use with water up to 70°C.
'H.B. Fuller UK Silicone Spray'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 4', dated '23/05/2025'. For use with water up to 85°C.
'Polypipe Silicone Spray Lubricant SG 300'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 2', dated 'November 2022'. For use with water up to 85°C.
'Greasil 4000'. White coloured silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'RADILON® S RV350RKC2 306 BK'. Black coloured, injection moulded, 35% glass fibre reinforced, PA6 material. For use with water up to 85°C.
'Badadur PBT9 GF10 WL Blau 1001'. Blue coloured, injection moulded PBT material. For use with water up to 23°C.
'ISO Resin Topaz-2100-AT'. Beige coloured polyester resin manufactured by hand layup. For use with water up to 45°C.
'GP Resin Topaz-1110-TP'. Beige coloured polyester resin material manufactured by hand lay-up. For use with water up to 45°C.
'Kuzeyboru HDPE 100 Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 23°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'EP7007PF 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EPDM-50AA2, EPDM-60AA2, EPDM-70AA2, EPDM-80AA2 & EPDM-85AA2'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 ShA & 85 ShA. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EPDM E293'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LR33'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.25mm. For use with water up to 23°C.
'N57140'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'1EP6052'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.12mm. For use with water up to 23°C.
'EPDM2019'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'S71U 'O' rings'. Off white coloured (translucent), compression moulded VMQ 'O' rings. Shore hardness 70. Tested in-radius size between 0.89mm & 2.85mm. For use with water up to 85°C.
'SIL60 RED 'O' rings and seals'. Red coloured, injection moulded silicone rubber 'O' rings and seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.25mm. The seals have a tested in-radius size of 0.90mm. For use with water up to 85°C.
‘40SIL310P, 45SIL310P, 50SIL310P(W), 55SIL310P, 60SIL3137P, 65SIL310P, 70SIL310P, 75SIL310P & 80SIL310P'. Compression moulded, silicone rubber ‘O’ rings in natural, white, black, red, blue, yellow & grey. Tested in-radius size 0.5mm. For use with water up to 85°C.
'RBL-9200KW'. Colourless, transparent silicone rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Silopren LSR 2742'. Colourless (translucent), compression moulded silicone elastomeric material. Shore hardness 38. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Born2Bond Aquafast Instant Adhesive'. Clear sealing compound. Apply as per manufacturer's TDS dated 'April 2022' and cure for 24 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Lettergold External Leak Sealer'. Clear silicone sealant. Apply as per manufacturer's TDS 'Version 1', dated '16/07/2025'. Cure for 96 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Grilamid TR 30 natural, TR 30 LS natural (appear colourless, translucent), TR 30 LS blue 4345, TR 30 LS blue 4387 & TR 30 LS blue 4396 (blue coloured)’. Injection moulded, PA 61/X materials. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193745 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 65 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 440 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 71 450 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a non-rising spindle headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member. Each inlet incorporates a combined washer and stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates a lever operated spherical valve and stainless-steel strainer. For use with BS EN1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of boiling water dispensers incorporating stainless steel water tank (3Ltr, 5Ltr, 10Ltr and 13Ltr) with inlet supply controlled via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. Maximum working pressure 7.0 Bar Maximum operating temperature 96.0°C
Range of one piece (black) plastic storage cisterns supplied with a screened vent. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-1 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-2 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-3 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No |
D30PF and D30PF-1 only different in the color of Item 11 and Item 13 D30PF-2 and D30PF-3 only different in the color of Item 11 and Item 13 DN30PF and D30PF-2 only different in the shape of Stem
Range of deck mounted ceramic cartridge and single sequential headwork assemblies, (brass bodies – various styles and finishes), incorporating a range of operating members. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic discs headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of thermostatic cartridges with plastic bodies and stainless-steel filters, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C
Thermostatic cartridges incorporating plastic bodies, for insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). incorporating a ceramic cartridge and single lever operating member with a spring loaded, pull down trigger operated spray. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 65°C.
Page 191 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
