Range of pressure relief valves incorporating brass bodies and EPDM rubber washers. The valves incorporate a manually operated rotational easing gear. For maximum working pressure please refer to model. Maximum operating temperature 99°C.
Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.
Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C
Spherical valve incorporating a brass body and ball, PTFE seat, EPDM and NBR ‘O’-rings. Maximum working pressure 10.0 bar. Cold water use only.
Range of spherical valves incorporating DZR brass bodies and balls (nickel plated), EPDM ‘O’-rings, PTFE seats and red or blue coloured lever type operating members. Maximum working pressure 16.0 bar for compression models Maximum working pressure 40.0 bar for 1¼”-2” RP Female & pressfit models Maximum working pressure 50.0 bar ½”-1” RP Female & pressfit models. Maximum operating temperature 85°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 bar. (Cold water use only).
Angled stop valve with a chrome plated brass body and NBR ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of stop valves incorporating brass bodies (brass or chrome plated) with EPDM ‘O’-rings and gaskets. Maximum working pressure 10.0 bar. Cold water use only.
Range of screw down stop valves with plastic bodies to be used with PEX, MDPE and copper pipe. For above ground use only. Maximum working pressure 16.0 bar, cold water use only.
Front loading, commercial washing machine. Flow is supplied via solenoid valves and the unit incorporates a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. Between 1st January 2021 to 22nd November 2021, the material is for use with water up to 50°C. Between 23rd November 2021 and 31st January 2026, the material is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RS-0004'. White coloured, compression moulded seal ring manufactured from 'ADR 96' ceramic material. For use with water up to 85°C.
'H-3500-6351-9221'. Grey coloured silicon carbide washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS dated '9 November 2015'. Cure for 210 seconds@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP01'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'V6.3' issued March 2019. For use with water up to 65°C.
'Intercrete 4807'. Site applied, grey coloured cementitious repair mortar. Mix 'Intercrete 4807' and water in a mass ratio of 9.4:1 Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Celanyl A3 WR GF30 BK 9005/Z/FA'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
Page 20 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
