'UP 5604 TP' (amber coloured) & 'UP- 4601 TPI' (pink coloured). Unsaturated polyester resin materials manufactured by hand lay-up. For use with water up to 50°C.
'Cosmoplast HDPE & MDPE Pipes'. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'Bingo HDPE Pipes 01'. Black coloured (with blue, external stripes), extruded HDPE pipe. For use with water up to 85°C.
'Bingo HDPE Fittings 02'. Black coloured, injection moulded HDPE fittings. For use with water up to 85°C.
'Hotace HDPE Black Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 80°C.
'Hengyuan PE100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
'Lubricomp CG006-NA1G003 Black'. Black coloured, injection moulded polystyrene material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EJ820 'O' ring'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP1/1/5 BLK EPDM Diaphragm'. Black coloured, compression moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'Corirubber 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'D0012'. Black coloured EPDM material manufactured by vulcanisation moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'70EP505p'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'70NB502S'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ZL-001 (blue coloured) & ZL-002 (red coloured) O-ring'. Compression moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ergo 4207 (yellow coloured), 4205 (white coloured) & 4453 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of electronic, touch free, wall-mounted taps (chromium plated brass. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, with either bottom entry (A28-06 XXX models) or side entry (A28-06 side). The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar Cold Water Use Only
Range of bottom entry BS1212-4 (2016) delayed or non delayed (all models)action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.
Floor mounted, single outlet (swivel) combination tap assembly (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel inter-locked shower hose incorporating an EPDM lining and NBR gaskets. Maximum operating temperature 85°C. Open outlet use only.
T-type thermostatic blending valve with a nickel plated brass body and EPDM ‘O’-rings. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spring loaded single check valve cartridges comprising of a POM body and cap, stainless steel spring and EPDM gasket and O-rings. Max working pressure 10 bar. Max operating temperature 85°C.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Non-verifiable double check valve assembly with DZR brass body consisting of two spring loaded, resilient trim in-line check valve cartridges, incorporating a lever operated spherical valve. Maximum working pressure 10 Bar Cold water use
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body and silicone seals. Maximum working pressure 5.0 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating a brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The outlets incorporate a plastic aerator. Model 63785-00XX incorporates a pull-out spray with push button trigger assembly. The pull-out spray incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Model 63787-00XX incorporates a pull-down outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Model 33528671 is supplied with a lever type pop up waste – not verified by test. Maximum working pressure - 10 Bar Maximum operating temperature - 70 °C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a quarter turn ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with a single lever operating member. The spout outlets incorporate an aerator. Models Prime, Specto and Linear have approved check valve cartridges in the inlets, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| H64DMT2 | Chrome | 15mm | 10 bar | 60 °C | Bristan | Handle | No | Single sequential | Metal Backnuts | Aerator | Flow Regulator Fitted, |
Range of two-hole, single outlet, fixed, combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever or cross-top operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 185 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
