'E70N01C 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have an in-radius size of 0.5mm. The gaskets have an in-radius size of 1.0mm. For use with water up to 85°C.
'ZF-73'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘EW45, EW50, EW53, EW54, EW54W, EW55, EW60, EW65, EW70, EW75, EW80, EW81 & EW85’. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 45 & 85. Tested in-radius size 1.4mm. For use with water up to 60°C.
'silicone RS7007'. Translucent, colourless, compression moulded silicone rubber material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'V-2 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'REGM20'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'MV250 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Flomasta 7619J'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
`Pool* Filetplast`. White coloured silicone paste. For use with water up to 85°C.
`Pâte d’étanchéité`. White coloured silicone paste. For use with water up to 85°C.
'Unecol PVC New Age Solvent Cement'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Marfran E DRW HOF 50A & Marfran E DRW HOF 90A'. Pale yellow coloured (transparent), injection moulded TPS-SEBS materials. Shore hardness between 50A & 90A. Tested in-radius size 1.1mm. For use with water up to 60°C.
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Bottom Entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. Incorporates plastic body and ½’’ BSP inlet. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The cistern incorporates an angled servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. There is a flow restrictor and stainless-steel strainer on the inlet valve. The cistern is operated by a manual push button. Maximum operating pressure 8.0 bar. Cold water use only.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
‘Calomax Eclipse’ range of electrically heated counter top or wall mounted catering water boilers. The boilers incorporate a stainless steel cold water feed cistern which has a combined vent/overflow fitted with an insect screen. The water to the cistern is supplied via a solenoid valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The water level is electronically controlled via level sensors. The water is dispensed via a manually operated brass bodied (chrome plated)/stainless steel bodied self-closing tap(s) or a push button controlling a solenoid valve prior to the outlet. The counter top models are supplied with a PVC coated flexible inlet hose (¾” BSP (F) x 15mm standpipe) and a push fit adaptor (15mm push fit x ¾ BSP (F)). Maximum working pressure 10.0 bar (to the solenoid valve). Maximum temperature of dispsensed water 90°C for PB3C10 & PB3W5 models and 97°C for all other models. Cold water supply only.
Range of single hole, single outlet (fixed spout with a swivel nozzle) over the rim bidet combination tap assemblies (various finishes). The taps incorporate quarter turn ceramic disc headwork with cross top or lever type operating members. The spout outlets have a plastic aerator and the products are supplied with a lever type pop-up waste. Maximum working pressure 5.0 bar Maximum operating temperature 60°C
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The product is supplied with metal backnuts. UK-1DPXX models only are a single feed and come with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole or two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPM-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPM-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPM-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPM-6DLN-00 & UMPM-7DLN- 00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole or two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPK-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPK-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPK-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPK-6DLN-00 & UMPK-7DLN-00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole (UMPU-1DLN-00 & UMPU-2DLN-00 models) or two hole (UMPU-6DLN-00 & UMPU-7DLN-00 models), single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPU-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPU-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPU-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPU-6DLN-00 & UMPU-7DLN-00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with plastic backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Single-hole single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a pull-out spray. The pull-out spray hose is stainless steel braided and has a. The pull-out spray outlet incorporates a button which changes and/or stops the flow of water, a plastic aerator and check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection.
Range of single hole, single outlet (swivel) pull down spray combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The connection between the body and the spout incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. The products are supplied with optional ½” BSP (F) x ⅜ BSP (M) brass adaptors and NBR washers for installation on each inlet hose. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The HV3 model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65 °C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow aerator. The AQE-DIP-301-CP model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating a ceramic cartridge headwork and single lever operating members however model 922034 is fitted with a non rising spindle headwork and dome type operating members. The spout outlet incorporates a plastic flow straightener on models: 922064, 922034, 922302, 922303, 922304 or flow straightener and aerator kit on models: 922311, 922312, 922313, and some models are supplied with a click waste. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating chromium plated brass bodies, ceramic cartridge headwork with single lever operating member. The spout outlets incorporate either a plastic aerator or flow straightener. The 2565T1EP, 2565T3EP & 3565T5EP models are supplied with a check valve cartridge and filter on the inlets, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The 2565T1, 2565T3 & 2565T5 models have flow restrictors on the inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating a ceramic cartridge headwork and either cross top or a single lever operating member. The spout outlets incorporate a plastic flow straightener and the products are supplied with lever operated pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes, see models) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied with either a lever type waste (model 39 034) or screw down waste (39 037). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) incorporating a ceramic cartridge headworks with single lever operating member. The spout outlets incorporate a plastic aerator. Model (PM BAS C) is supplied with a lever type pop-up waste. Maximum operating pressure 7.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk head works with cross top operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disk headworks with cross top operating members. The spout outlet incorporates either a plastic aerator or a flow straighter. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disc headworks with cross-top operating members. The inlet hose assemblies incorporate a servicing valve and is supplied with a single check valve assembly verified by test (suitable for backflow protection against Fluid Category 2). The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headwork with cross-top operating members. The inlet hose assemblies incorporate a servicing valve and is supplied with a single check valve assembly verified by test (suitable for backflow protection against Fluid Category 2). The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 18 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
