Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of wall and ceiling mounted shower outlets with chromium plated brass bodies supplied with various styled chromium plated shower arms. The shower head inlet incorporates a flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower elbows/holders with brass or stainless-steel bodies (various finishes). The elbows incorporate a plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models VOLA 070-XX & VOLA 070R-XX are supplied with a shower hose and handset.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets with plastic bodies. The inlets incorporate a stainless-steel strainer and a built-in flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower heads with plastic bodies (various finishes), incorporating plastic strainer or flow restrictor and EPDM o rings with stainless-steel strainers on the inlets. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with plastic bodies (various finishes), EPDM O-rings and a stainless-steel strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets (ABS bodies - various finishes, see model), incorporating NBR and EPDM ‘O’ rings that incorporate stainless-steel mesh strainers.
Non-metallic materials and components comply with BS6920 at 70°C
Shower kit consisting of a shower handset and shower hose incorporating a riser rail assembly.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower kits, (various finishes - see model), comprising of a shower hose (brass double interlocked, PEX lined) and a shower handset. Maximum operating temperature 60°C.
Bib taps incorporating either brass or DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating member. Spout oultlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of nylon braided PEX lined flexible hose assemblies. Maximum operating temperature 60°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘TAQ’ range of stainless steel or grey nylon braided (indicated by ACB in model name), EPDM lined flexible hose assemblies, incorporating various end connections. Some of the possible end connections also incorporate EPDM washers, gaskets or ‘O’-rings. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel indirect (single or twin coil), direct and heat pump unvented hot water storage cylinders. The heat pump models also incorporate a plate heat exchanger and a circulation pump. The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@90.0˚C. The products are supplied with an inlet control group consisting of an adjustable pressure reducing valve, adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 bar, a strainer, am expansion relief valve set at 6.0 bar and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The products are also supplied with an immersion heater, an expansion vessel (12, 19 or 24 litres depending on model) and a tundish. Maximum supply pressure to the inlet control group: 16.0 bar. Maximum working pressure: Secondary circuit: 5.5 Bar. Primary Circuit: 6.0 Bar (All models except for the Direct - DI prefix models). Maximum operating temperature 75°C.
Range of air vent valves with brass (covered with blue polyester coated ductile iron body) or plastic bodies and plastic floats. Maximum working pressure 16.0 bar (AP models) or 25.0 bar (AQ models). Cold water use only.
Range of automatic air venting valves incorporating epoxy coated, ductile iron bodies and plastic float. Maximum operating pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of automatic air venting valves with brass bodies, stainless steel strainer, plastic float and EPDM ‘O’-rings and gaskets. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted, thermostatic blending valves incorporating ceramic disc diverter cartridges. Inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to verify backflow protection. Product also had manual override button. Model VM207X and variants are supplied with variations of dome and single lever operating members. Model VM208X and variants are supplied with varaitions of cube type operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The valve can be supplied with a variation of shower kits that can consist of the following components: handsets, overhead showers, shower hoses, wall outlets, fixed arms, and isolation valves. Maximum working pressure 7 bar. Maximum working temperature 65°C.
Page 164 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
