'Isoglas H30FVL (c) NA'. Translucent, off-white coloured, injection moulded, polypropylene material. For use with water up to 85°C.
'INFB001'. Black coloured, compression moulded butyl rubber material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
'EPDM60BKFG, EPDM65BKFG, EPDM70BKFG, EPDM75BKFG & EPDM80BKFG'. Black coloured, compression moulded EPDM rubbers. Shore hardness between 60A & 80A. Tested in-radius size 1.0mm. For use with water up to 70°C.
0713.23/60 (shore hardness 60A). 0713.23/65 (shore hardness 65A). 0713.23/70 (shore hardness 70A). 0713.23/75 (shore hardness 75A). 0713.23/80 (shore hardness 80A). 0713.23/85 (shore hardness 85A). Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E2532'. Black coloured, compression moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'JSP/SF-02'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
`SACHDEVA/EPDM-80`. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius 1.1mm. For use with water up to 23°C.
'VI701/KTW'. Black coloured, injection moulded FKM 'O'-ring, shore hardness 70, tested in-radius 1.5mm. For use with water up to 85°C.
'WN70/3 BLK NBR 'O' rings. Black coloured, injection moulded 'O' rings. Shore hardness 70. Tested in-radius size of 1.0mm For use with water up to 23°C.
'7PD1612 washers'. Black coloured, extruded NBR rubber washers. Tested in-radius size 1.4mm. Shore hardness 70. '7PD1612 'O' rings'. Black coloured, injection moulded NBR rubber `O` rings. Tested in-radius size 0.9mm. Shore hardness 70. Both for use with water up to 60°C.
'CHEMILINE AH001 FB 026'. Black coloured, niltrile rubber material manufactured by calendaring and curing. Shore hardness 70A. Tested in-radius size 1.1mm. For use with water up to 65°C.
‘NGP 60 T (Translucent – off-white), NGP 60 T/R (Transy Red), NGP 60 BK (Black), NGP 60 GY (Grey) & NGP 60 W (White)’. Extruded, platinum cured, silicone rubber tubing. Shore hardness 60. Tested in-radii sizes between 0.75mm & 1.5mm. For use with water up to 85°C
'Tangit PVC-U Plus'. Light yellow (straw) coloured, solvent cement. Apply as per manufacturer's TDS 'Tangit PVC-U PLUS TDS 070917 EN'. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
A range of single-hole, single outlet (fixed (model 62816) or swivel (models 63407)) electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding 63407) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Incorporating a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator (SH-T9050N model) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 161 of 554
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
