'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'PC IR2200, Housing'. Clear (transparent), injection moulded polycarbonate housing component. For use with water up to 65°C.
'ELYDAN'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 40°C.
'+GF+ Hakan HDPE PE100 Pipes'. Extruded PE100 pipes which are either blue coloured or black coloured (with blue stripes). For use with water up to 23°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'DELAV HDPE Pipe PE100' and 'DELAV HDPE Pipe PE100-RC'. Black coloured (with blue stripes), extruded PE pipes. For use with water up to 23°C.
'TORELINA® A670MWR1B'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Visulfon' range of injection moulded PPSU materials which includes grades: K002 A8Y-G0048 (off-white). K002 BK001 (black). B002 NC001 (natural, appears amber). B002 BK001 (black). B002 A8Y-G0048 (off-white). For use with water up to 85°C.
'AquaTerra SDR 6 PP-R Pipes'. Green coloured, extruded PP-R pipes. 'AquaTerra SDR 7.4 PP-R Pipes', green coloured, extruded PP-R pipes were added to the approval in September 2024. All pipes are or use with water up to 85°C.
'+GF+ Hakan Aquasystem Faser Composite Stabil Pipe'. Multi-layered, extruded PPR pipe consisting of a white coloured inner, green coloured middle and white coloured outer layer. The following multi-layered, extruded PPR pipes were added to the approval in April 2025: Green coloured inner, green coloured middle and green coloured outer layer. Beige coloured inner, green coloured middle and beige coloured outer layer. Grey coloured inner, green coloured middle and grey coloured outer layer. For use with water up to 85°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
'Hepworth uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'SPIT ViPer XTREM'. grey coloured (once mixed), two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'VIPER XTREM | 2023-1'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E7108 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'E7108 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
‘EPDM EV2’. Black coloured, injection moulded EPDM materials. Shore hardness 75A. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'OLDAL 460'. Black coloured, injection moulded EPDM material. Shore hardness 50. Tested in-radius size 1.2mm. For use with water up to 85°C.
'E7083AA'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E8083AA'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CH EP 172 DM'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SE-808PF'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7037K'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Pango2023'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'S7107'. Red coloured, injection moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'RBL-9200-20, RBL-9200-30, RBL-9200-40, RBL-9200-50, RBL-9200-60, RBL-9200-65 & RBL-9200-70'. Transparent, colourless injection moulded silicone rubber materials. Shore hardness between 20 & 70. Tested in-radii size between 0.75mm & 2.89mm. For use with water up to 85°C.
'Cemprotec 2000-S Waterproofing Tape'. White coloured, elastomeric tape manufactured by lamination. Apply as per manufacturer's Product Data Sheet dated August 2023. For use with water up to 23°C.
'Weld-on 747 blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's product data sheet and cure for 4 hours@5°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-on 721 ECO blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's product data sheet and cure for 12 hours@5°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-on 717 ECO Grey'. Grey coloured solvent cement. ‘Weld-On 746 ECO Pool Blue PVC Cement’ was added to the approval in September 2025. Apply as per manufacturer's product data sheet and cure for 24 hours@5°C. For use with water up to 40°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘THERMOLAST DW Compound series (DW/CS2)’. Natural (appears white), injection moulded TPE-S materials. The materials can be coloured and include the following grades: DW(1)OCX-(2): (1) – for "0" to "8" indicating hardness: DW5OCX-(2) (55 ShA). DW6OCX-(2) (65 ShA). DW7OCX-(2) (75 ShA). DW8OCX-(2) (85 ShA). DW0OCX-(2) (35 ShD). (2) - Extension of 4 digits indicating colour. The four digits stands for this: LCNT -> natural material without colour. All other numbers depends on colour. The first digit of the 4 digit colour code indicates the ground colour: 1 = yellow, 2 = orange, 3 = red, 4 = violet, 5 = blue, 6 = green, 7 = grey, 8 = brown & 9 = white or black. The other digits of the 4 digit colour code, indicates the particular shade. For use with water up to 85°C.
‘Wall mounted, electronically operated tap assemblies (brass bodies - in various finishes). The flow is controlled by a solenoid valve that is actuated via an infra-red sensor on the spout. The spout outlet incorporates plastic aerators. Maximum working pressure 6 bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve that is activated via an infrared sensor. The spout outlet incorporates an aerator. Maximum working pressure: 8.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Spring loaded in-line check valve cartridges for insertion into pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
AXOR UNO Range of single-hole, single outlet, (fixed) over the rim bidet combination tap assemblies, (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever or dome type operating members. The spout outlets incorporate plastic aerators. The products are supplied with lever operated pop-up waste (not verified by test). Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of quarter turn ceramic disc or non-rising spindle headworks (see models) with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone rubber gaskets for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 90.0°C
Range of ceramic cartridge headworks with plastic bodies, some of which include a diverter function. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Integrated magnetic headwork with EPDM ‘O’-rings and gaskets for insertion into specifically dimensioned bores. The headwork is operated by a push-button that moves a magnetic pillar, which in turn attracts the magnetic seal ring causing the valve to open, when the button is released the magnetic pillar travels back and the seal ring returns and the valve closes. The product incorporates a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with plastic or brass bodies, for insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Thermostatic cartridges with a plastic body and stainless-steel strainer mesh. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 139 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
