'Jotaguard VA 5001'. Blue coloured, factory applied, Fusion Bonded Epoxy Powder Coating. Apply as per manufacturer's application guide dated 'October 2018'. Cure for 5 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CanSEALER (CS1)-TS'. Site applied, colourless waterproofing sealer which can be applied to cement with a roller or a brush. Apply one coat with a roller or a brush as per manufacturer's Technical Data Sheet 'CS1-210002'. Cure for 36 days@5°C. When applied by brush the material is for use with water up to 23°C. When applied by roller the material is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TPU inner hose (YOUSHI/3017)'. Transparent, colourless, extruded TPU hose. For use with water up to 85°C.
`VIP Universal Pipe Lubricant`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet issued 'Nov 2019'. For use with water up to 23°C.
'Zytel® FG101L NC010 & Zytel® FG42A NC010'. Un-pigmented (appear off-white, translucent), injection moulded nylon materials. For use with water up to 23°C.
'Zytel® HTNFG52G35HSLR BK011'. Black coloured, injection moulded polyphthalamide (PPA) material. For use with water up to 85°C.
'Ultramid D3EG10 FC Aqua Black 23285'. Black coloured, injection moulded polyamide material. For use with water up to 65°C.
'Badadur PBT9 GF30 Natur S1' (appears cream in colour) and 'Badadur PBT9 GF30 grau 930a' (grey coloured). Natural or grey coloured, injection moulded, glass reinforced PBT materials. For use with water up to 85°C.
'Pocan B1700 000000'. Natural (appears white in colour), injection moulded PBT material. For use with water up to 23°C.
'IRRIPLASTEC PE 100 WATER'. Dual layered, extruded pipe comprising of a white coloured (opaque), PE inner layer and a black coloured, PE outer layer. For use with water up to 23°C.
'Al Jubail PE100 Pipe'. Black coloured, extruded HDPE Pipe. For use with water up to 70°C.
'Lupolen 3621 M RM'. Off-white coloured, roto-moulded MDPE material. For use with water up to 23°C.
‘Xytron™ G4020DW-FC BK00001 & Xytron™ G3020DW-FC BK00001’. Black coloured, injection moulded PPS materials. In September 2023 ‘Xytron G4020DW-FC NA99001’, natural (appears beige), injection moulded PPS material was added to the approval. All are for use with water up to 85°C.
'4270' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. In May 2024 ‘shaped seals’ (in-radius of 1.8mm) made in Italy, were added to the approval. In November 2024, lip seals (in-radius of 0.7mm) made in Italy, were added to the approval. For use with water up to 85°C.
'VL1713M266B Black'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.02mm. For use with water up to 85°C.
Page 133 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
