Range of lever operated spherical valves incorporating brass bodies (nickel plated), brass balls (chrome plated) and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chrome plated brass ball and PTFE seats with tee-handles or lever type or extension stem type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of spherical valves with brushed chrome brass bodies, chrome plated brass ball incorporating a PTFE seat and NBR O rings. For use with EN1057 copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Gate valve with an blue epoxy coated cast iron body, EPDM packing and seal. The valve operates via a hand wheel. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of angle valves (chromium plated brass bodies) with EPDM O-rings and washers. The products incorporate non-rising spindle headworks with dome type operating members. Maximum working pressure 10 bar. Maximum working temperature 80°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of in line double regulating valves with DZR brass bodies, EPDM ‘O’-rings and PTFE valve seals. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function with a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'Delrin® FG511DP NC010'. White coloured, injection moulded semi-opaque acetal material. For use with water up to 85°C.
'ABS-NBK White & ABS-NBK 1C Grey'. White or grey coloured, injection moulded ABS materials. For use with water up to 85°C.
'SOLID-02'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's user instructions 'File No.: SOLID-0069, Vison: SLD-03, Date of issue: 2015-01-01'. Cure for 2 hours @60°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-001G Two Component Epoxy Resin Coating/Ceramic Epoxy Coating'. Factory applied, off-white coloured, two-component epoxy coating. Components A and B are preheated to 60°C, mixed in a volume ratio of 1:1.& applied as per manufacturer's instructions 'version 2.00', dated '11/01/2021'. Cure for 1 hour@60°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'issue reference SPI 20170215' dated 21st January 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT (grey)'. Factory applied, grey coloured, epoxy powder coating. Apply as per manufacturer's TDS dated January 21st 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 132 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
