'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of float operated valves with brass bodies manufactured to BS1212 Part 2 1990. The valves have ½’’ BSP inlets with plastic backnuts, brass or plastic back plates, an up and over type outlet discharge and a brass lever arm. Maximum working pressure 14.0 bar. For use with cold water only.
Range of float operated valves with plastic bodies and either brass or plastic inlet tails of the side or bottom entry type manufactured to BS1212 Part 3 1990. The valves have ½’’ BSP inlets with plastic backnuts, an up and over type outlet discharge and a plastic operating lever adjusted by a screw & lock nut. Maximum working pressure 14.0 bar. For cold water use only.
Range of BS1212 Part 3 1990 float operated valves incorporating plastic bodies of either the side or bottom entry type. Maximum working pressure 14.0 bar. For cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
A range of spring-loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic disc and cartridge headworks with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Manual click type cartridge headwork with plastic body. EPDM seals and plastic strainer for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
Range of single hole, single outlet (swivel) pull down spray combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The connection between the body and the spout incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. The products are supplied with optional ½” BSP (F) x ⅜ BSP (M) brass adaptors and NBR washers for installation on each inlet hose. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a pull-down spout with a plastic aerator, which also incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with optional ⅜” BSP (M) x ½” BSP (F) adaptors each with two fibre gaskets for installation on each inlet hose. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted single-hole, single outlet, fixed, combination tap assembly with a brass body in a variety of finishes (See models). Incorporating a ceramic disc headwork with a dome type operating member. The temperature is controlled separately via a rotary ceramic cartridge headwork that can also be used as a shut off with a dome type operating member. The inlets to the tap incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and plastic flow regulator. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products can be supplied with a pop-up or click type waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products can be supplied with waste outlets (see models). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model A05406 has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Page 13 of 60
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
