Range of brass and copper end feed fittings for use with copper pipe (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251202002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

Endex and size on body of fitting

Installation Requirements:

R001

Expiry date:

31/12/2030

Model:

N6 - Reducer, larger end male - 88310 (66.7 x 28mm), N6 - Reducer, larger end male - 88311 (66.7 x 35mm), N6 - Reducer, larger end male - 88312 (66.7 x 42mm), N6 - Reducer, larger end male - 88313 (66.7 x 54mm), N6 - Reducer, larger end male - 89624 (76.1 x 35mm), N6 - Reducer, larger end male - 89625 (76.1 x 42mm), N6 - Reducer, larger end male - 89626 (76.1 x 54mm), N6 - Reducer, larger end male - 89630 (108 x 42mm), N6 - Reducer, larger end male - 89631 (108 x 54mm), N6 - Reducer, larger end male - 89699 (133 x 42mm), N6 - Reducer, larger end male - 89700 (133 x 54mm), N6 - Reducer, larger end male - 89704 (159 x 54mm), N25 - Tee, reduced branch - 88807 (66.7mm x 28mm), N25 - Tee, reduced branch - 89055 (66.7mm x 35mm), N25 - Tee, reduced branch - 89056 (66.7mm x 42mm), N25 - Tee, reduced branch - 89057 (66.7mm x 54mm), N25 - Tee, reduced branch - 89058 (76.1mm x 28mm), N25 - Tee, reduced branch - 89000 (76.1mm x 35mm), N25 - Tee, reduced branch - 89654 (76.1mm x 42mm), N25 - Tee, reduced branch - 89001 (76.1mm x 54mm), N25 - Tee, reduced branch - 89059 (108mm x 35mm), N25 - Tee, reduced branch - 89660 (108mm x 54mm), N25 - Tee, reduced branch - 89715 (133mm x 54mm), N25 - Tee, reduced branch - 89717 (159mm x 54mm),

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Range of blue epoxy coated carbon steel flanged dismantling joints with EPDM sealing rings. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.

Section:

1220 Fittings for use with Tube and Pipe

Section Subtitle:

Flanged, un-flanged and repair clamps. (external clamps only) Unless specified in the individual approval, the products within this section are not suitable for below ground use WRAS takes no responsibility for the claims made by the manufacturer regarding the effectiveness of the product for providing a repair to fittings to prevent a waste of water.

WRAS Approval Number:

260115010

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN65-DN1600 flanged.

Marking:

KSB logo, KSB, model, DN, PN and material on data plate on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

ECOLINE DJ DISMANTLING JOINTS

Approval Holder:

KSB Valves (Changzhou) Co., Ltd.

Company Name

KSB Valves (Changzhou) Co., Ltd.

Address

No.68 Huanbao Four Road, Xinbei District, Changzhou, Jiangsu Province

Country

China

View All Listings by this Company

Manufacturer:

KSB Valves (Changzhou) Co., Ltd.

Company Name

KSB Valves (Changzhou) Co., Ltd.

Address

No.68 Huanbao Four Road, Xinbei District, Changzhou, Jiangsu Province

Country

China

View All Listings by this Company

Range of dual flush, WC outlet valves operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.

Section:

1305 Valves

Section Subtitle:

Flushing valve(s) for WC Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

251202729

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

62mm OD

Marking:

Miellat, model & WRAS on body.

Installation Requirements:

R001 R556 R571

Expiry date:

31/12/2030

Model:

M4050WR

Approval Holder:

Miellat Industries LLC

Company Name

Miellat Industries LLC

Address

Unit B-24, KEZAD Logistics Park, 2 Al Zaeem St, Khalifa Industrial Zone Abu Dhabi

Country

U.A.E

General Email

info@miellat.com

View All Listings by this Company

Type ‘J’ range of plate heat exchangers with stainless steel (AISI 304L or AISI 316L) fin and end plates. Maximum working pressure 3.0 bar (primary circuit) and 10.0 bar (secondary circuit). Maximum operating temperature 80°C.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) Primary circuit. ½” BSP (M) Sanitary circuit.

Marking:

Condevo S.p.A. and model on adhesive label on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

Type ‘J’ range comprising of: PP10FJX. PP12FJX. PP14FJX. PP16FJX. PP18FJX. PP20FJX. PP22FJX. PP24FJX. PP26FJX. PP28FJX. PP30FJX. PP32FJX. PP34FJX. X denotes the body material and is replaced with: 4 = AISI304L 6 = AISI316L

Approval Holder:

Condevo SpA

Company Name

Condevo SpA

Address

Via Luna, Z.A. 26866 Marudo (LO) Italy

View All Listings by this Company

Range of copper brazed, stainless steel (316) heat exchangers in various sizes (4-300 plates, see models). Maximum working pressure: see models. Maximum operating temperature: 99°C.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” - 3” BSP (M).

Marking:

SWEP, models, PN and tech info on adhesive label on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

X8T-SC-S - Number or Plates: MIN 4 – MAX 60, Max Flow rate – 4 m3/h - ½”, ¾” - 32/26bar. 10T-SC-M - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 9 m3/h - 3/8” to 1 ¼” - 41/36bar. 15T-SC-M - Number or Plates: MIN 4 – MAX 60, Max Flow rate – 4 m3/h - ½” to 1” - 45/45bar. 16DW-SC-S - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 11,3 m3/h ½” to 1 ¼” - 16/16bar. 16DW-SC-M - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 11,3 m3/h - ½” to 1 ¼” - 45/45bar. 220-SC-S - Number or Plates: MIN 4 – MAX 300, Max Flow rate – 39 m3/h 1” to 2 ½” -25/25bar. 320HT-SC-S - Number or Plates: MIN 4 – MAX 300, Max Flow rate – 61,7 m3/h - 1 ½” to 2 ½” - 33/29bar. 320LT-SC-S - Number or Plates: MIN 4 – MAX 260, Max Flow rate – 76,2 m3/h - 1 ½” to 3” - 25/25bar.

Approval Holder:

SWEP International AB

Company Name

SWEP International AB

Address

Järvgatan 3B, Box 105, 26122 Landskrona

Country

Sweden

View All Listings by this Company

Manufacturer:

SWEP International AB/SWEP Slovakia s.r.o.

Company Name

SWEP International AB/SWEP Slovakia s.r.o.

Address

Box 105, 26122, Landskrona

Country

Sweden

Phone

+46 418400406

View All Listings by this Company

Range of electronically controlled heat interface units (HIU) with a stainless-steel plate heat exchanger providing space heating and instantaneous hot water. The domestic hot water (secondary) circuit incorporates a pressure relief valve (set at 10.0 bar). The inlets and outlets of all circuits incorporate a T-handled spherical valve. Maximum working pressures: 10.0 bar (Primary circuit), 9.5 Bar (Secondary circuit). Maximum operating temperature 95°C. Cold supply only.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

260102725

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

IRN R511 applies to all spherical valves that can be used for draining the system down.

Size:

1½” BSP (M).

Marking:

Oventrop Logo on body.

Installation Requirements:

R001 R140 R360 R511

Expiry date:

31/01/2031

Proviso:

Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with Schedule 2 paragraph 7 of the Water Supply (Water Fittings) Regulations 1999.

Model:

1681580 - Requmaq X-80, 1681480 - Requmaq X-70.

Approval Holder:

Oventrop GmbH & Co KG

Company Name

Oventrop GmbH & Co KG

Address

Paul-Oventrop-Strasse 1, 59939 Olsberg

Country

Germany

View All Listings by this Company

Range of electromagnetic water meters with stainless steel bodies, dark grey ebonite rubber inner liner and stainless-steel (SUS316L) electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN25 - DN1000 flanged.

Marking:

Q&T INSTRUMENT CO.,LTD., model number, DN size, electrode material (316L), pressure, serial number “YYMMXXXX”, flow arrow and other technical information on adhesive label on body.

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

QTLD-X Where: X is replaced by a number between 25 and 1000 to denote (DN) size, e.g., QTLD-25.

Approval Holder:

Q&T INSTRUMENT CO.，LTD.

Company Name

Q&T INSTRUMENT CO.，LTD.

Address

1 Wangbai Road, Huanglong Industrial Zone, Kaifeng City, Henan Province

Postcode

47500

Country

China

Phone

(0086-371)2666-5538

General Email

xiaoyanzhao@huitiantiefulong.com

View All Listings by this Company

Manufacturer:

Q&T INSTRUMENT CO.，LTD.

Company Name

Q&T INSTRUMENT CO.，LTD.

Address

1 Wangbai Road, Huanglong Industrial Zone, Kaifeng City, Henan Province

Postcode

47500

Country

China

Phone

(0086-371)2666-5538

General Email

xiaoyanzhao@huitiantiefulong.com

View All Listings by this Company

Range of ultrasonic water meters with brass and plastic bodies. The inlets incorporate plastic strainers. Maximum working pressure 16.0 bar. Maximum operating temperature 50⁰C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN15 – ½” BSP (M), DN20 – ¾” BSP (M), DN25 – 1” BSP (M), DN32 – 1 ¼” BSP (M), DN40 – 1 ½” BSP (M), DN50 – 2” BSP (M).

Marking:

Flow arrow on plastic body and brass inlet outlet tube, manufacturers logo, barcode, size and technical data laser etched on plastic cover

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

IWU 200 (Iskrasonic®2000)

Approval Holder:

ISKRAEMECO ENERGY MANGEMENT

Company Name

ISKRAEMECO ENERGY MANGEMENT

Address

Plot #1-Pyramids Industrial West Park 10th of Ramadan City

Country

Egypt

View All Listings by this Company

Manufacturer:

ISKRAEMECO ENERGY MANGEMENT

Company Name

ISKRAEMECO ENERGY MANGEMENT

Address

Plot #1-Pyramids Industrial West Park 10th of Ramadan City

Country

Egypt

View All Listings by this Company

Water shock absorber incorporating a stainless-steel body and EPDM membrane. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

Aquasystem logo (brand of Zilio Industries SpA), model code, date of manufacture (DD/MM/YYYY), pressure and other technical information on adhesive label on body.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

XVES050000 0.16L (pre-set 5.0 bar) & XVES050001 0.16L (pre-set 1.5 bar) Potable water shock arrestor.

Approval Holder:

Reliance Worldwide Corporation (UK)

Company Name

Reliance Worldwide Corporation (UK)

Address

Horton Road, West Drayton

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Manufacturer:

Zilio Industries SPA

Company Name

Zilio Industries SPA

Address

Via Sega Vecchia, 65 Località Friola 36050 Pozzoleone (Vicenza)

Country

Italy

Phone

[+39] 049 59 57 552

General Email

info@zilioindustries.com

View All Listings by this Company

Manufacturer:

Zilio Industries SPA

Company Name

Zilio Industries SPA

Address

Via Sega Vecchia, 65 Località Friola 36050 Pozzoleone (Vicenza)

Country

Italy

Phone

[+39] 049 59 57 552

General Email

info@zilioindustries.com

View All Listings by this Company

Range of pressure transmitters with stainless steel bodies. Maximum working pressure 100.0 Bar Maximum operating temperature 80.0°C (Type 540) or 100.0°C (Type 520 & Type 522)

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models

Marking:

Huba Control logo and technical info on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

Type 520: Dimension, Sealing type, Male/Female Thread 7/16"-20 UNF, sealing cone 45°, Female 7/16"-20 UNF, sealed at front ISO 11926-1 Male G1/4", sealed at front, Female 1/2"-14 NPT, thread sealing, Male 1/2"-14 NPT, thread sealing, Female 7/16"-20 UNF, sealing cone 45°, Male G1/8", sealed at front, Male G1/4", sealed at back without sealing groove, Male G1/4", sealed at back ISO 1179-2, Male G1/4", sealed at back + Manometer, Male G1/4", sealed at front, Female G1/4", sealed at front + Manometer, Male G1/4", sealed at back DIN 3852-2, Male R1/4", thread sealing EN 10226, Male G1/2", sealed at front, Male M20x1.5, sealed at front + Manometer, Male 7/16"-20 UNF, sealing cone with schrader, Female Type 522: Dimension, Sealing type, Male/Female Thread 7/16"-20 UNF, sealing cone 45°, Female 1/2"-14 NPT, thread sealing, Female 7/16"-20 UNF, sealing cone 45°, Male G1/4", sealed at back ISO 1179-2, Male G1/4", sealed at back + Manometer, Male G1/2", sealed at front, Male G1/2", sealed at front + Manometer, Male M20x1.5, sealed at front + Manometer, Male Type 540: Dimension, Sealing type, Male/Female Thread G1/4", sealed at front, Female 7/16"-20 UNF, sealing cone 45°, Male G1/4", sealed at back ISO 1179-2, Male R1/4", thread sealing EN 10226, Male Additional Information The pressure orifice and the connectors are all made from stainless steel X2CrNiMo17-12-2/1.4404 / AISI316L. The Schrader is made from Stainless X8CrNi18-9/1.4305/303 All variants can use the following pressure cell options, based on application requirements: -1…9 Bar / 0…2.5 - 100 bar (Stainless Steel Cell X6Cr17-1.4016) The only difference between the models 520, 522 & 540 is the input and output signal, and the approvals (not relevant to WRAS) All the different type variants can be given a unique customer article number, to trace the full specification: Example: 520.99XXX 520 = Model Type 99 = Client / project specific number XXX = Unique file for client containing all the above options specified within model.

Manufacturer:

Huba Control AG

Company Name

Huba Control AG

Address

Industriestrasse 17, CH-5436 Wurenlos, Switzerland

View All Listings by this Company