'KH369R'. Black coloured, compression moulded Carbon ring which is impregnated with Phenolic Resin. For use with water up to 85°C.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'Rubalit IS95 White'. White coloured, dry pressed ceramic disc component. For use with water up to 85°C.
'YJ-AL2O3 95%'. White coloured, dry pressed and sintered ceramic disc. For use with water up to 85°C.
'CD 101 Grey Sealing Disc'. Grey coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Rubalit A1896 Sealing Disc'. White coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBVL EX400G – RAL 5005 Blue & RAL 5017 Blue'. Factory applied, blue coloured epoxy coatings. Apply as per manufacturer’s datasheet ‘PDS/APPPG/V01/01-2024’. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBPC EX405SG INTER GREEN'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's data sheet 'PDS/APPPG/V02/01-2024'. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Alsen FBE Blue Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'AIPL 1212/1', dated '07/06/2023'. Cure for 2.5 hours:235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBERPOX-2K-DS-LACKFARBE (IV81 & IW81)’ – blue coloured and ‘LUBERPOX-2K-DS-LACKFARBE (IV81812 & IW81)’ – red coloured’. Factory applied, two component, epoxy coatings consisting of IV81 or IV81812 (base) and IW81 (hardener). Mix IV81 or IV81812 (base) & IW81 (hardener) in a mass ratio of 5:1 or volume ratio of 3.5:1 and apply as per manufacturer’s data sheets ‘Rev: 04 – 04.12.2023’ (blue) or ‘Rev: 03 – 04.12.2023’ (red). Cure for 20 minutes@22°C and then 40 minutes@75°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JBG-SRPC Plus'. Factory applied, sulphate resisting Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JBG-OPC Plus'. Factory applied, grey coloured, ordinary Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ecoflex PEX hose'. Off-white coloured (translucent, extruded, single layered PEX hose. For use with water up to 85°C.
‘G. BESLUX BESSIL EHV-00’. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 85°C.
'Spectrum Nylon Mesh'. White coloured, extruded nylon mesh. For use with water up to 85°C.
'INSTAFLEX & iFIT'. Grey coloured, extruded PB pipes. For use with water up to 85°C.
'GF Instaflex PB Fitting'. Grey coloured, injection moulded polybutylene fitting. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 TM-Z1 grau 930a'. Grey coloured, injection moulded polybutylene terephthalate material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 grau 930a'. Grey coloured, injection moulded PBT material. For use with water up to 85°C.
'LEXAN EXL1494T-NA8A005T'. Colourless, injection moulded Polycarbonate material. For use with water up to 85°C.
'Unidelta Uniterm PEX Pipe'. Off-white coloured (opaque), extruded PEX pipe. For use with water up to 85°C.
'PIMTAS PLASTIK PE 100 Pipes'. Extruded, PE100 pipes available in black and blue colours. For use with water up to 85°C.
'SCGC HDPE H1000PC'. Black coloured, extruded polyethylene material. For use with water up to 85°C.
'Binh Minh Plastic's PP-R pipe’. Blue coloured (with green stripe), extruded PP-R pipe. For use with water up to 85°C.
'Cosmoplast PP-R Pipe'. Green coloured, extruded PP-R pipe. For use with water up to 85°C.
'Spectrum Polypropylene Felt'. White coloured, extruded polypropylene felt material. For use with water up to 85°C.
'PTFE G439'. Terracotta coloured, extruded PTFE sealing ring. For use with water up to 85°C.
'WRAS 61713 EB 78'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 78D. Tested in-radius size 1.05mm. For use with water up to 60°C.
'WRAS 61813 E80'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 2.2mm. For use with water up to 60°C.
'EPDM4570‐70'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
'M534 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'M534 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'60EP126p'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.6mm. For use with water up to 85°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E59WKZ'. Black coloured, injection moulded EPDM rubber material. Shore hardness 58. Tested in-radius 1.0mm. For use with water up to 60°C.
'WN12/7/1 BLK 'O'-rings'. Black coloured, injection moulded NBR 'O' rings. Tested in-radii sizes between 0.89mm and 2.0mm. Shore hardness 70. For use with water up to 65°C.
'2MS70-55R Seals, Washers, Gaskets and 'O' rings'. Red coloured, injection moulded silicone seals, washers, gaskets and 'O' rings. Shore hardness 70. Seals have a tested in-radius size between 0.25mm & 8,0mm. Washers, gaskets and 'O' rings have a tested in-radius size of 8.0mm. For use with water up to 85°C.
'HCR 9230, HCR 9250, HCR 9270 & HCR 9280'. Natural (appear white, translucent), compression moulded silicone rubber materials. Shore hardness between 30 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'10' range of extruded, silicone rubber material available in translucent (which appears off-white), black, white, red and blue colours. Shore hardness between 40 & 70. Tested in-radii sizes between 0.15mm & 6.0mm. For use with water up to 85°C. A full list of the individual product codes included on this approval is available from WRAS.
‘Trutite Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.3’, dated 12/02/24 and this material is only approved for these conditions. For use with water up to 85°C.
‘CORE® Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.2’, dated 12/01/23 and this material is only approved for these conditions. For use with water up to 85°C.
‘Drei Bond 5204’. Yellow coloured anaerobic adhesive paste. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'PLIMAT PVC Pressure Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6311689/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test, suitable for backflow prevention against Fluid Category 5). Maximum working pressure 7.5 bar. Cold water supply only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (either black finish or chromium plated brass bodies). Flow is controlled by a solenoid valve which is actuated via an infra-red sensor. The spout incorporates a stainless-steel strainer on the outlet. The product is supplied with a stainless steel braided PEX lined flexible hose assembly and a combination valve with a DZR brass body consisting of a servicing valve, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a stainless-steel strainer and plastic flow regulator on the outlet. The combination valve has a compression inlet for use with copper pipe (manufactured to BS EN 1057). The tap incorporates a soap dispenser with a separate dispensing nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 91 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
