Directory Search Results

Print List

#240904726

‘PREMIX’ range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both the domestic hot water and primary circuit are controlled via spherical valves. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 80°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
240904726
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
22mm compression (Primary Circuit) 15mm compression (Secondary Circuit)
Marking:
E.C.A. on front cover. E.C.A, model and technical information including KW rating on adhesive label on body.
Installation Requirements:
R001 R360
Expiry date:
30/09/2029
Model:
8116350010 CALORA PREMIX 24 HM ERP UK 8116484110 CALORA PREMIX 14 HM ERP UK 8116487110 CALORA PREMIX 20 HM ERP UK 8116356010 CALORA PREMIX 28 HM ERP UK 8116389010 CITIUS PREMIX 14 HM ERP UK 8116392010 CITIUS PREMIX 20 HM ERP UK 8116353010 CITIUS PREMIX 24 HM ERP UK 8116380010 CITIUS PREMIX 28 HM ERP UK 8116576110 Proteus Premix 42 HM DG ERP UK 8116550010 Proteus Premix 45 HM DG ERP UK
Product Images

Approval Holder:
Emas Makina Sanayi A.S.
Company Name
Emas Makina Sanayi A.S.
Address
Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa
Postcode
45030
Country
Turkey
General Email
egecakmakci@emas.com.tr

View All Listings by this Company
Manufacturer:
Emas Makina Sanayi A.S.
Company Name
Emas Makina Sanayi A.S.
Address
Mustafa Kemal Blv. No:13 Keçiliköy Osb/Yunusemre Manisa
Postcode
45030
Country
Turkey
General Email
egecakmakci@emas.com.tr

View All Listings by this Company

Print This Approval


#2103042

Range of rotating piston, volumetric in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1505 Water Meters
Size:
¾” BSP - 2” BSP (M) inlet and outlet.
Marking:
George Kent on lid.
Installation Requirements:
R001
Expiry date:
31/03/2026
Model:
GKMV30 - DN15, 20, 25, 30 & 40

Approval Holder:
George Kent (Malaysia) Berhad
Company Name
George Kent (Malaysia) Berhad
Address
1115 Blok A, Jalan Puchong, Taman Meranti Jaya, 47120 Puchong, Selangor Darul Ehsan
Country
Malaysia

View All Listings by this Company

Print This Approval


#241002010

Range of in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:
1505 Water Meters
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
¾” BSP (M) to 1½” BSP (M)
Marking:
ZENNER on cover. Flow arrow on body. Zenner and product info on meter face.
Installation Requirements:
R001
Expiry date:
31/10/2029
Model:
IUWS hydr. 2,5-110-1/2 D-cell IUWS hydr. 2,5-165-1/2 D-cell IUWS hydr. 2,5-170-1/2 D-cell IUWS hydr. 2,5-190-1/2 D-cell IUWS hydr. 4-105-3/4 D-cell IUWS hydr. 4-130-3/4 D-cell IUWS hydr. 4-165-3/4 D-cell IUWS hydr. 4-190-3/4 D-cell IUWS hydr. 4-220-3/4 D-cell IUWS hydr. 10-150-1 D-cell IUWS hydr. 10-160-1 D-cell IUWS hydr. 10-160-5/4 D-cell IUWS hydr. 10-260-5/4 D-cell IUWS hydr. 16-150-6/4 D-cell IUWS hydr. 16-200-6/4 D-cell IUWS hydr. 16-300-6/4 D-cell IUWS hydr. 25-300-2 D-cell
Product Images

Approval Holder:
Zenner International Gmbh & Co. KG
Company Name
Zenner International Gmbh & Co. KG
Address
Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany
Country
Germany

View All Listings by this Company
Manufacturer:
Zenner Meters (Shanghai) Ltd.
Company Name
Zenner Meters (Shanghai) Ltd.
Address
No 15 Dongxing Road Songjiang Ind Zone Shanghai
Country
China

View All Listings by this Company

Print This Approval


#241002014

Range of IUW ultrasonic water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature: 50°C.

Section:
1505 Water Meters
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
See models below, note all sizes listed in DN are flanged connections.
Marking:
Zenner, DN, Year of manufacture (YYYY) and technical information on dial face. Size & flow arrow on body.
Installation Requirements:
R001
Expiry date:
31/10/2029
Model:
IUW Q3-25, DN50, Length 200mm IUW Q3-25, DN50, Length 270mm IUW Q3-25, DN50, Length 300mm IUW Q3-40, DN65, Length 200mm IUW Q3-40, DN65, Length 300mm IUW Q3-63, DN80, Length 225mm IUW Q3-63, DN80, Length 300mm IUW Q3-63, DN80, Length 225mm IUW Q3-63, DN80, Length 200mm IUW Q3-100, DN100, Length 360mm IUW Q3-100, DN100, Length 350mm IUW Q3-100, DN100, Length 250mm IUW Q3-160, DN125, Length 250mm IUW Q3-250, DN150, Length 300mm IUW Q3-250, DN150, Length 500mm IUW Q3-400, DN200, Length 350mm IUW Q3-630, DN250, Length 450mm IUW Q3-1000, DN300, Length 500mm
Product Images

Approval Holder:
Zenner International Gmbh & Co. KG
Company Name
Zenner International Gmbh & Co. KG
Address
Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany
Country
Germany

View All Listings by this Company

Print This Approval


#241002027

Range of in-line water meters with brass bodies and plastic turbines. The inlets incorporate plastic filters, and the outlets incorporate non-return valves (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 65.0°C.

Section:
1505 Water Meters
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M) ¾” BSP (M 1¼” BSP M, 1½” BSP M, 2” BSP
Marking:
Janz logo, model code and other info on meter box
Installation Requirements:
R001
Expiry date:
31/10/2029
Model:
Smartio DN15 Q3=2,5 R*** Smartio DN20 Q3=2,5 R*** Smartio DN20 Q3=4 R*** Models added August 2025: Smartio DN25 Q3=6,3 R*** Smartio DN32 Q3=10 R*** Smartio DN40 Q3=16 R*** Body lengths: DN25: 150mm/160mm/175mm/198mm*/220mm*/260mm* DN32: 150mm/160mm/200mm*/220mm*/260mm* DN40: 150mm/200mm/300mm* *It’s possible to put a non-return valve (NRV)
Product Images

Manufacturer:
Janz Contagem e Gestão de Fluidos, SA
Company Name
Janz Contagem e Gestão de Fluidos, SA
Address
Av. Infante D. Henrique nº 286 Lisboa
Postcode
1950-421
Country
Portugal
Phone
00351 21 831 6000

View All Listings by this Company

Print This Approval


#240902065

Range of ‘Thermowatt’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C

Section:
1530 Miscellaneous Fittings
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
RT – 1.1/4” BSP (M) to 2.1/4” BSP (M) RF – 48 mm OD
Marking:
Thermowatt logo, Model, Voltage, Size and other information on cap.
Installation Requirements:
R001
Expiry date:
30/09/2029
Model:
Model Code: XXYZS Where XX denotes the boss type and can be replaced with any of the following: RT = Thread Type RF = Flange Type Where Y denotes the heating tube material and can be replaced with any of the following: 1 = Copper 2 = AISI 304 / AISI 304L 3 = AISI 321 4 = AISI 316 / AISI 316L 5 = Alloy 800 / Alloy 825 / Alloy 840 6 = Titanium 7 = AISI 309S 8 = AISI 310 Where Z denotes the brazing system and can be replaced with any of the following: A = Tin Alloy B = Silver Alloy C = Itek Brazing Where S denotes the surface enamelling and can be replaced with either of the following: S = Enamelled Blank = Not Enamelled
Product Images

Approval Holder:
Thermowatt S.p.A.
Company Name
Thermowatt S.p.A.
Address
Via San Giovanni Battista 21 Arcevia
Postcode
60011
Country
Italy
Phone
+39 0731988246
General Email
thermowatt@legalmail.it

View All Listings by this Company

Print This Approval


#241004701

Range of two, three or four pump booster sets, with vertical multistage pumps comprising of pressure vessels, stainless steel manifolds, pressure gauges, spherical valves and EPDM O-rings. Maximum working pressure - 10.0 bar. Max operating temperature - Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
241004701
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
Flanged - DN50 - DN100 - See models.
Marking:
Adhesive label on panel with company (Dutypoint), model & technical info including pressures.
Installation Requirements:
R001 R415
Expiry date:
31/10/2029
Model:
VRX2-05-XXXX - DN50, VRX2-10-XXXX - DN65, VRX2-15-XXXX - DN80, VRX2-22-XXXX - DN80, VRX3-05-XXXX - DN50, VRX3-10-XXXX - DN65, VRX3-15-XXXX - DN80, VRX3-22-XXXX - DN80, VRX4-05-XXXX - DN65, VRX4-10-XXXX - DN80, VRX4-15-XXXX - DN100, VRX4-22-XXXX - DN100. Note, XXXX on end of model codes above denotes motor size and type. Example of model number: VRX2-10-040T Range: VRX Number of pumps: 2 Nominal Flow rate (m3/hr): 10 Motor kw (without decimal): 040 (4kw) Voltage T (T=400/3/50 M=230/1/50)
Product Images

Approval Holder:
Dutypoint Ltd.
Company Name
Dutypoint Ltd.
Address
Unit A, Quedgeley West Business Park, Hardwicke, Gloucester
Postcode
GL2 4PA
Country
United Kingdom
Phone
01452313334
General Email
austin.hill@dutypoint.com

View All Listings by this Company

Print This Approval


#241004717

Range of two, three and four pump cold water booster sets. The products incorporate a suction and discharge manifold and pumps. Maximum working pressure 10 bar. Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
241004717
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1” inlet and 1” outlet 1 ¼” inlet and 1” outlet 1 ½” inlet and 1 ¼” outlet 2” inlet and 1 ½” outlet 2” inlet and 2” outlet 2 ½” inlet and 2” outlet 3” inlet and 2 ½” outlet 3” inlet and 3” outlet
Marking:
Stuart Turner, model and product info on adhesive label on back of control box.
Installation Requirements:
R001 R415
Expiry date:
31/10/2029
Model:
SP1V-3HM04S-VARiFLO-8 SP1V-3HM06S-VARiFLO-8 SP1V-3HM08S-VARiFLO-8 SP1V-3HM10S-VARiFLO-8 SP1V-3HM12S-VARiFLO-8 SP1V-5HM04S-VARiFLO-8 SP1V-5HM06S-VARiFLO-8 SP1V-5HM08S-VARiFLO-8 SP1V-5HM10S-VARiFLO-8 SP1V-5HM12S-VARiFLO-8 SP1V-10HM03S-VARiFLO-8 SP1V-10HM04S-VARiFLO-8 SP1V-10HM06S-VARiFLO-8 SP1V-15HM03S-VARiFLO-8 SP2V-3HM04S-VARiFLO-24 SP2V-3HM06S-VARiFLO-24 SP2V-3HM08S-VARiFLO-24 SP2V-3HM10S-VARiFLO-24 SP2V-3HM12S-VARiFLO-24 SP2V-5HM04S-VARiFLO-24 SP2V-5HM06S-VARiFLO-24 SP2V-5HM08S-VARiFLO-24 SP2V-5HM10S-VARiFLO-24 SP2V-5HM12S-VARiFLO-24 SP2V-10HM03S-VARiFLO-24 SP2V-10HM04S-VARiFLO-24 SP2V-10HM06S-VARiFLO-24 SP2V-15HM03S-VARiFLO-24 SP3V-3HM04S-VARiFLO-24 SP3V-3HM06S-VARiFLO-24 SP3V-3HM08S-VARiFLO-24 SP3V-3HM10S-VARiFLO-24 SP3V-3HM12S-VARiFLO-24 SP3V-5HM04S-VARiFLO-24 SP3V-5HM06S-VARiFLO-24 SP3V-5HM08S-VARiFLO-24 SP3V-5HM10S-VARiFLO-24 SP3V-5HM12S-VARiFLO-24 SP3V-10HM03S-VARiFLO-24 SP3V-10HM04S-VARiFLO-24 SP3V-10HM06S-VARiFLO-24 SP3V-15HM03S-VARiFLO-24 SP1V-0304-VARiFLO-8 SP1V-0306-VARiFLO-8 SP1V-0308-VARiFLO-8 SP1V-0310-VARiFLO-8 SP1V-0312-VARiFLO-8 SP1V-0504-VARiFLO-8 SP1V-0506-VARiFLO-8 SP1V-0508-VARiFLO-8 SP1V-0510-VARiFLO-8 SP1V-0512-VARiFLO-8 SP1V-1003-VARiFLO-8 SP1V-1004-VARiFLO-8 SP1V-1006-VARiFLO-8 SP1V-1503-VARiFLO-8 SP2V-0304-VARiFLO-24 SP2V-0306-VARiFLO-24 SP2V-0308-VARiFLO-24 SP2V-0310-VARiFLO-24 SP2V-0312-VARiFLO-24 SP2V-0504-VARiFLO-24 SP2V-0506-VARiFLO-24 SP2V-0508-VARiFLO-24 SP2V-0510-VARiFLO-24 SP2V-0512-VARiFLO-24 SP2V-1003-VARiFLO-24 SP2V-1004-VARiFLO-24 SP2V-1006-VARiFLO-24 SP2V-1503-VARiFLO-24 SP3V-0304-VARiFLO-24 SP3V-0306-VARiFLO-24 SP3V-0308-VARiFLO-24 SP3V-0310-VARiFLO-24 SP3V-0312-VARiFLO-24 SP3V-0504-VARiFLO-24 SP3V-0506-VARiFLO-24 SP3V-0508-VARiFLO-24 SP3V-0510-VARiFLO-24 SP3V-0512-VARiFLO-24 SP3V-1003-VARiFLO-24 SP3V-1004-VARiFLO-24 SP3V-1006-VARiFLO-24 SP3V-1503-VARiFLO-24 SP1V-CM3-3-VARiFLO-8 SP1V-CM3-5-VARiFLO-8 SP1V-CM3-7-VARiFLO-8 SP1V-CM3-9-VARiFLO-8 SP1V-CM3-11-VARiFLO-8 SP1V-CM5-3-VARiFLO-8 SP1V-CM5-5-VARiFLO-8 SP1V-CM5-7-VARiFLO-8 SP1V-CM5-9-VARiFLO-8 SP1V-CM5-11-VARiFLO-8 SP1V-CM10-2-VARiFLO-8 SP1V-CM10-3-VARiFLO-8 SP1V-CM10-5-VARiFLO-8 SP1V-CM15-2-VARiFLO-8 SP2V-CM3-3-VARiFLO-24 SP2V-CM3-5-VARiFLO-24 SP2V-CM3-7-VARiFLO-24 SP2V-CM3-9-VARiFLO-24 SP2V-CM3-11-VARiFLO-24 SP2V-CM5-3-VARiFLO-24 SP2V-CM5-5-VARiFLO-24 SP2V-CM5-7-VARiFLO-24 SP2V-CM5-9-VARiFLO-24 SP2V-CM5-11-VARiFLO-24 SP2V-CM10-2-VARiFLO-24 SP2V-CM10-3-VARiFLO-24 SP2V-CM10-5-VARiFLO-24 SP2V-CM15-2-VARiFLO-24 SP3V-CM3-3-VARiFLO-24 SP3V-CM3-5-VARiFLO-24 SP3V-CM3-7-VARiFLO-24 SP3V-CM3-9-VARiFLO-24 SP3V-CM3-11-VARiFLO-24 SP3V-CM5-3-VARiFLO-24 SP3V-CM5-5-VARiFLO-24 SP3V-CM5-7-VARiFLO-24 SP3V-CM5-9-VARiFLO-24 SP3V-CM5-11-VARiFLO-24 SP3V-CM10-2-VARiFLO-24 SP3V-CM10-3-VARiFLO-24 SP3V-CM10-5-VARiFLO-24 SP3V-CM15-2-VARiFLO-24 SP2V-3HM04S-VARiFLO-18 SP2V-3HM06S-VARiFLO-18 SP2V-3HM08S-VARiFLO-18 SP2V-3HM10S-VARiFLO-18 SP2V-3HM12S-VARiFLO-18 SP2V-5HM04S-VARiFLO-18 SP2V-5HM06S-VARiFLO-18 SP2V-5HM08S-VARiFLO-18 SP2V-5HM10S-VARiFLO-18 SP2V-5HM12S-VARiFLO-18 SP2V-10HM03S-VARiFLO-18 SP2V-10HM04S-VARiFLO-18 SP2V-10HM06S-VARiFLO-18 SP2V-15HM03S-VARiFLO-18 SP3V-3HM04S-VARiFLO-18 SP3V-3HM06S-VARiFLO-18 SP3V-3HM08S-VARiFLO-18 SP3V-3HM10S-VARiFLO-18 SP3V-3HM12S-VARiFLO-18 SP3V-5HM04S-VARiFLO-18 SP3V-5HM06S-VARiFLO-18 SP3V-5HM08S-VARiFLO-18 SP3V-5HM10S-VARiFLO-18 SP3V-5HM12S-VARiFLO-18 SP3V-10HM03S-VARiFLO-18 SP3V-10HM04S-VARiFLO-18 SP3V-10HM06S-VARiFLO-18 SP3V-15HM03S-VARiFLO-18 SP2V-0304-VARiFLO-18 SP2V-0306-VARiFLO-18 SP2V-0308-VARiFLO-18 SP2V-0310-VARiFLO-18 SP2V-0312-VARiFLO-18 SP2V-0504-VARiFLO-18 SP2V-0506-VARiFLO-18 SP2V-0508-VARiFLO-18 SP2V-0510-VARiFLO-18 SP2V-0512-VARiFLO-18 SP2V-1003-VARiFLO-18 SP2V-1004-VARiFLO-18 SP2V-1006-VARiFLO-18 SP2V-1503-VARiFLO-18 SP3V-0304-VARiFLO-18 SP3V-0306-VARiFLO-18 SP3V-0308-VARiFLO-18 SP3V-0310-VARiFLO-18 SP3V-0312-VARiFLO-18 SP3V-0504-VARiFLO-18 SP3V-0506-VARiFLO-18 SP3V-0508-VARiFLO-18 SP3V-0510-VARiFLO-18 SP3V-0512-VARiFLO-18 SP3V-1003-VARiFLO-18 SP3V-1004-VARiFLO-18 SP3V-1006-VARiFLO-18 SP3V-1503-VARiFLO-18 SP2V-CM3-3-VARiFLO-18 SP2V-CM3-5-VARiFLO-18 SP2V-CM3-7-VARiFLO-18 SP2V-CM3-9-VARiFLO-18 SP2V-CM3-11-VARiFLO-18 SP2V-CM5-3-VARiFLO-18 SP2V-CM5-5-VARiFLO-18 SP2V-CM5-7-VARiFLO-18 SP2V-CM5-9-VARiFLO-18 SP2V-CM5-11-VARiFLO-18 SP2V-CM10-2-VARiFLO-18 SP2V-CM10-3-VARiFLO-18 SP2V-CM10-5-VARiFLO-18 SP2V-CM15-2-VARiFLO-18 SP3V-CM3-3-VARiFLO-18 SP3V-CM3-5-VARiFLO-18 SP3V-CM3-7-VARiFLO-18 SP3V-CM3-9-VARiFLO-18 SP3V-CM3-11-VARiFLO-18 SP3V-CM5-3-VARiFLO-18 SP3V-CM5-5-VARiFLO-18 SP3V-CM5-7-VARiFLO-18 SP3V-CM5-9-VARiFLO-18 SP3V-CM5-11-VARiFLO-18 SP3V-CM10-2-VARiFLO-18 SP3V-CM10-3-VARiFLO-18 SP3V-CM10-5-VARiFLO-18 SP3V-CM15-2-VARiFLO-18 Models added August 2025: AH1-XXXX-XXX-X - Flowboost AH, AH2-XXXX-XXX-X - Flowboost AH, AH3-XXXX-XXX-X - Flowboost AH. Where: XXXX = PUMP MODEL CODE, XXX = KW SIZE REFERENCE, X = VOLTAGE. AH1-0304L-003-M AH1-0306L-005-M AH1-0308L-007-M AH1-0310L-007-M AH1-0312L-011-M AH1-0504L-005-M AH1-0506L-011-M AH1-0508L-011-M AH1-0510L-015-M AH1-0512L-022-M AH1-1003L-011-M AH1-1004L-015-M AH1-1006L-022-M AH1-1503L-022-M AH2-0304L-003-M AH2-0306L-005-M AH2-0308L-007-M AH2-0310L-007-M AH2-0312L-011-M AH2-0504L-005-M AH2-0506L-011-M AH2-0508L-011-M AH2-0510L-015-M AH2-0512L-022-M AH2-1003L-011-M AH2-1004L-015-M AH2-1006L-022-M AH2-1503L-022-M AH3-0304L-003-M AH3-0306L-005-M AH3-0308L-007-M AH3-0310L-007-M AH3-0312L-011-M AH3-0504L-005-M AH3-0506L-011-M AH3-0508L-011-M AH3-0510L-015-M AH3-0512L-022-M AH3-1003L-011-M AH3-1004L-015-M AH3-1006L-022-M AH3-1503L-022-M AH1-0304L-007-M AH1-0306L-011-M AH1-0308L-015-M AH1-0310L-022-M AH1-0312L-022-M AH1-0504L-011-M AH1-0506L-015-M AH1-0508L-022-M AH1-0510L-022-M AH1-0512L-022-M AH1-1003L-011-M AH1-1004L-015-M AH1-1006L-022-M AH1-1503L-022-M AH2-0304L-007-M AH2-0306L-011-M AH2-0308L-015-M AH2-0310L-022-M AH2-0312L-022-M AH2-0504L-011-M AH2-0506L-015-M AH2-0508L-022-M AH2-0510L-022-M AH2-0512L-022-M AH2-1003L-011-M AH2-1004L-015-M AH2-1006L-022-M AH2-1503L-022-M AH3-0304L-007-M AH3-0306L-011-M AH3-0308L-015-M AH3-0310L-022-M AH3-0312L-022-M AH3-0504L-011-M AH3-0506L-015-M AH3-0508L-022-M AH3-0510L-022-M AH3-0512L-022-M AH3-1003L-011-M AH3-1004L-015-M AH3-1006L-022-M AH3-1503L-022-M
Product Images

Approval Holder:
Dutypoint Ltd.
Company Name
Dutypoint Ltd.
Address
Unit A, Quedgeley West Business Park, Hardwicke, Gloucester
Postcode
GL2 4PA
Country
United Kingdom
Phone
01452313334
General Email
austin.hill@dutypoint.com

View All Listings by this Company

Print This Approval


#241004726

Range of horizontal multistage close coupled centrifugal pumps incorporating stainless steel cased bodies and impellers. Maximum working pressure: See models. Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
241004726
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1” BSP (F) - 3” BSP (F). DN40 - DN80 flange.
Marking:
Calpeda and technical info on data plate.
Installation Requirements:
R001 R415
Expiry date:
31/10/2029
Model:
MXH Series: (304 stainless models) MXH/MXHM 202, 203, 204, 205, 206 – 1 ¼” x 1” – 8 bar. MXH/MXHM 402, 403, 404, 405, 406 – 1 1/2” x 1” – 8 bar. MXH/MXHM 802, 803, 804, 805 – 2 ¼” x 1 1/2” – 8 bar. MXH/MXHM 1602, 1603, 1604, 1605, 1606 – 2 ¼” x 1 1/2” – 8 bar. MXH/MXH-F 2001, 2002, 2003, 2004, 2005 – 2 ¼” x 1 1/2” – 10 bar. MXH/MXH-F 3201, 3202, 3203, 3204 – 2 1/2” x 2” – 10 bar. MXH/MXH-F 4801, 4802, 4803 – 3” x 2 1/2” – 10 bar. (316 stainless models) MXHL/MXHLM 202, 203, 204, 205, 206 - 1 ¼” x 1” – 8 bar. MXHL/MXHLM 402, 403, 404, 405, 406 - 1 ¼” x 1” – 8 bar. MXHL/MXHLM 802, 803, 804, 805 - 1 1/2” x 1” – 8 bar. ‘F’ in the code indictates flanged connection. There are four numbers to identify pump’s size: the first two indicate the flow rate (in m3/h); the second two indicate the number of stage (ex. Mxh 3204: 32 m3/h, 4 stages; mxh 203: 2 m3/h, 3 stages) A letter may be added at the end of the pump model to identify the current motor model fitted to the pump e.g. MXH203* where * can be E, /A, /B, /C etc. Example MXH203/A, MXH204/B etc.
Product Images

Approval Holder:
Calpeda S.p.A
Company Name
Calpeda S.p.A
Address
Via Roggia Di Mezzo 39 36050 Montoro Vicentino Vicenza
Country
Italy

View All Listings by this Company

Print This Approval


#241002708

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
241002708
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.
Size:
U 3S & U 5S models: 1” BSP (F) inlet x 1” BSP (F) outlet. U 7S models: 1¼” BSP (F) inlet x 1” BSP (F) outlet. U 9S models: 1½” BSP (F) inlet x 1¼” BSP (F) outlet. U 18S models: 2” BSP (F) inlet x 1½” BSP (F) outlet.
Marking:
Pentax logo, model code and other technical information on data plate on body.
Installation Requirements:
R001 R415
Expiry date:
31/10/2029
Model:
ULTRA S range: U X(S) - XX/Y (T) Where: U = pump type (ULTRA), X = Nominal flow-rate m³/h (3, 5, 7, 9, 18 see model list), S = ULTRA S range - stainless steel hydraulic part, XX = nominal power HPx100 (50 - 400 see model list), Y = Number of impellers (2 - 7 see model list), T = 3 phase, [blank] = single phase. U 3S models: U 3S-50/2; U 3S-70/3; U 3S-90/4; U 3S-100/5; U 3S-120/6; U 3S-150/7. U 5S models: U 5S-70/2; U 5S-80/3; U 5S-120/4; U 5S-150/5; U 5S-180/6; U 5S-200/7. U 7S models: U 7S-100/2; U 7S-120/3; U 7S-180/4; U 7S-250/5; U 7S-300/6. U 9S models: U 9S-100/2; U 9S-150/3; U 9S-200/4; U 9S-250/5. U 3S models: U 3S-50/2 T; U 3S-70/3 T; U 3S-90/4 T; U 3S-100/5 T; U 3S-120/6 T; U 3S-150/7 T. U 5S models: U 5S-70/2 T; U 5S-80/3 T; U 5S-120/4 T; U 5S-150/5 T; U 5S-180/6 T; U 5S-200/7 T. U 7S models: U 7S-100/2 T; U 7S-120/3 T; U 7S-180/4 T; U 7S-250/5 T; U 7S-300/6 T; U 7S-350/7 T. U 9S models: U 9S-100/2 T; U 9S-150/3 T; U 9S-200/4 T; U 9S-250/5 T. U 18S models: U 18S-180/2 T; U 18S-250/3 T; U 18S-400/4 T.
Product Images

Approval Holder:
PENTAX INDUSTRIES SpA
Company Name
PENTAX INDUSTRIES SpA
Address
Viale dell’Industria 1 Veronella
Postcode
37040
Country
Italy
Phone
+39 0442 489567
General Email
g.cengia@pentax-pumps.it

View All Listings by this Company
Manufacturer:
PENTAX INDUSTRIES SpA
Company Name
PENTAX INDUSTRIES SpA
Address
Viale dell’Industria 1 Veronella
Postcode
37040
Country
Italy
Phone
+39 0442 489567
General Email
g.cengia@pentax-pumps.it

View All Listings by this Company

Print This Approval


#240902064

EASO range of shower head and hand showers, with ABS bodies and chromium plated finish. Open outlet use. Maximum operating temperature - 65 °C.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
240902064
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M). 1/2" BSP (F) - (models 11102315 and 11102275 only).
Marking:
EASO and WRAS on Face of shower head – models 11102315 and 11102275 only. EASO and WRAS on base of hand shower – All Other.
Installation Requirements:
R001 R040
Expiry date:
30/09/2029
Model:
11102315 – Overhead shower, 11102275 – Overhead shower, 11101050 – Hand shower, 1110104901 – Hand shower, 1110104902 – Hand shower, 11101208 – Hand shower, 11101253 – Hand shower, 11101301 – Hand shower, 11101191 – Hand shower, 1110110501 – Hand shower, 1110110502 – Hand shower, 11101346 – Hand shower, 11101276 – Hand shower, 11101328 – Hand shower, 11101192 – Hand shower, 11101355 – Hand shower, 11101324 – Hand shower, 11101368 – Hand shower.
Product Images

Approval Holder:
Xiamen EASO Co., Ltd.
Company Name
Xiamen EASO Co., Ltd.
Address
4-5th Floor, No. 1020, Guankou Middle Road, Jimei District, Xiamen City, Fujian Province, 361023
Country
China

View All Listings by this Company

Print This Approval


#240908009

Range of shower outlets comprising of shower heads all incorporating stainless-steel strainer washers (plastic bodies-various finishes) and handheld showers (plastic bodies - various finishes). Maximum operating temperature 75°C.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
240908009
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
Open outlet use only
Size:
Shower heads – ½” BSP (F) Shower handsets- ½” BSP (M).
Marking:
Company logo and ‘Shower - A Shower A Solution’ on body.
Installation Requirements:
R001 R040
Expiry date:
30/09/2029
Model:
Showerheads: A10701, A12701, A10801, A14801, A14703, A12801, A15801, A15301, A15305, A10401, A15901, Shower Handsets: B10201, B81330, B11201, B80631, B80431, B81530, B30201, B30208, B32030, B32034, B31730, B31930, B10801, B10901, B81031, B91330, B32930, B32930-W, B32930-B, B91630, B91635, B91636, B32531, B91840.
Product Images

Approval Holder:
KAIPING HANSHUN SANITARY WARE INDUSTRIAL CO., LTD.
Company Name
KAIPING HANSHUN SANITARY WARE INDUSTRIAL CO., LTD.
Address
61 East Jinshan Road, Shuikou Town, Kaiping City, Jiangmen, Guangdong, China
Phone
0086‐13422793423
General Email
ada@ashower.com

View All Listings by this Company
Manufacturer:
KAIPING HANSHUN SANITARY WARE INDUSTRIAL CO., LTD.
Company Name
KAIPING HANSHUN SANITARY WARE INDUSTRIAL CO., LTD.
Address
61 East Jinshan Road, Shuikou Town, Kaiping City, Jiangmen, Guangdong, China
Phone
0086‐13422793423
General Email
ada@ashower.com

View All Listings by this Company

Print This Approval


#241188001

Range of overhead shower and shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
241188001
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
Shower handsets - ½” BSP (M) Overhead showers – ½” BSP (F)
Marking:
PPI on body
Installation Requirements:
R001 R040
Expiry date:
30/11/2029
Model:
VIC065 XXX HS124 XXX L102 XXX HS108 XXX HS304 XXX HS305 XXX HS326 XXX HS327 XXX HS328 XXX HS135 XXX HS159 XXX HS165 XXX HS182 XXX HS204 XXX HS166 XXX HS139 XXX HS161 XXX HS138 XXX HS162 XXX Additional information. (list any further information regarding the product or range, e.g.: key for model code, prefix/suffixes describing finishes, variants of operating member, etc.) XXX Denotes the finish: Chrome – No suffix, Brushed brass – BGP & Matt Black – MBK.

Approval Holder:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company
Manufacturer:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company

Print This Approval


#2310168

Range of overhead shower outlets with Various finishes. The inlets incorporate a stainless-steel strainer and flow regulator. Models 64400250CH, 67400250BBL, 63400250BBR, 68400250MB & 61400250BRZ Incorporates a shower arm.

Non-metallic materials and components comply with BS6920 at 60°C

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
2310168
Note:
Open outlet use only.
Size:
½” BSP F ½” BSP M Stainless Steel Braided PEX lined hose ½” BSP captive nut
Marking:
JTP on connector
Installation Requirements:
R001 R040
Expiry date:
31/10/2028
Model:
IX200, 23200BBR, 27200BBL, 28200MB, 21200BRZ, IX250, 23250BBR, 27250BBL, 28250MB, 21250BRZ, IX300, 23300BBR, 27300BBL, 28300MB, 21300BRZ, 32250, 38250MB, 33250BBR, 37250BBL, 64400250CH, 67400250BBL, 63400250BBR, 68400250MB & 61400250BRZ

Approval Holder:
Just Taps Plus UK Ltd
Company Name
Just Taps Plus UK Ltd
Address
Innovia House, Marish Wharf, St Mary's Rd, Langley
Postcode
SL3 6DA
Country
Berkshire
Phone
01895 44 22 11
General Email
info@jtpuk.co.uk

View All Listings by this Company

Print This Approval


#241004032

Range of shower handsets and overhead showers, (plastic bodies - various finishes). The inlets incorporate a plastic flow restrictor and stainless steel strainer. Maximum operating temperature 60°C. Open outlet use only.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
241004032
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M) Handset ½” BSP (F) Overhead shower
Marking:
Methven or Satinet on body
Installation Requirements:
R001 R040
Expiry date:
31/10/2029
Model:
48212 265901 265907 AOHSBK AOHSCPUK ECO01 KRLFHSBB KRLFHSBK KRLFHSBN KRLFHSCP KRLFHSGM KRLFWSCP OSQ230CP SJK005 SJK005-LF SJK23 SJK23-LF X-SJK23
Product Images

Approval Holder:
Methven UK Limited
Company Name
Methven UK Limited
Address
3-3A Stone Cross Court Yew Tree Way Golborne Warrington
Postcode
WA3 3JE
Country
United Kingdom
Phone
0800 195 1602
General Email
raluca.olariu@uk.methven.com

View All Listings by this Company

Print This Approval


#240904719

Flow sensor with a plastic and brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.

Section:
1718 Switches
Section Subtitle:
Flow control.
WRAS Approval Number:
240904719
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
18.9mm ID manifold connection
Marking:
SERKO Flow, model & flow arrow on body.
Installation Requirements:
R001
Expiry date:
30/09/2029
Model:
0003.7000.xxx T1301 Flow sensor. ‘xxx’ denotes different electrical connections.
Product Images

Approval Holder:
SERDAR PLASTIK SANAYİ VE TİCARET A.Ş
Company Name
SERDAR PLASTIK SANAYİ VE TİCARET A.Ş
Address
Türkmenistan Caddesi No:3 1.Organize Sanayi Bölgesi 06935 Sincan ANKARA

View All Listings by this Company
Manufacturer:
SERDAR PLASTIK SANAYİ VE TİCARET A.Ş
Company Name
SERDAR PLASTIK SANAYİ VE TİCARET A.Ş
Address
Türkmenistan Caddesi No:3 1.Organize Sanayi Bölgesi 06935 Sincan ANKARA

View All Listings by this Company

Print This Approval


#241002031

Range of self-closing basin taps (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic aerator, and the products are supplied with metal backnuts. Maximum operating pressure 7 Bar Maximum operating temperature 55 °C

Section:
1820 Taps
Section Subtitle:
Self closing tap(s).
WRAS Approval Number:
241002031
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M)
Marking:
Heshan Manbong logo KK Faucet on operating member
Installation Requirements:
R001 R006
Expiry date:
31/10/2029
Model:
W030G W032 W045 – E12
Product Images

Manufacturer:
Heshan Manbong Plumbing CO.,LTD.
Company Name
Heshan Manbong Plumbing CO.,LTD.
Address
No. 39, North Industrial Avenue , Zhishan Town, Heshan City, Guangdong Province, China

View All Listings by this Company

Print This Approval


#240402080

Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C

Section:
1860 Tubes
Section Subtitle:
Plastic hoses.
WRAS Approval Number:
240402080
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP captive nut. M15x1. All connection sizes can be used with every model of hose.
Marking:
IW, WRAS & year of manufacture (YYYY) on connector
Installation Requirements:
R001
Expiry date:
30/04/2029
Model:
Model:IW-XXXXXXXX 1st X stands for out diameter: from 13mm to 17mm +/-0.3mm (PVC tube use size 14mm and 15mm) 2nd X stands for outer material: S=stainless steel, B=brass, P=PVC,(PVC outer tube only with PVC inside tube) 3rd X stands for the surface treatment: C=chrome plated, P=stainless steel natural color, B=black, S=sliver, G=Gold,/Gray 4th X stands for fittings material: B=brass, S=stainless steel, Z=Zinc Alloy P=ABS 5th X stands for fittings size and shape: 1/2’ 3/8’ M15x1, M16x1,(M15*1,M16*1 use brass material only use size 13mm and 14mm only) Fitting shape find the attached1. 6th X stands for hose nipple material: B=brass, S=stainless steel, P=POM, N=Nylon 7th X stands for inner tube material:, PVC, EPDM,PEX (EPDM,PEX, tube only use with stainless steel and brass out side) 8th X stands for hose length from 10cm to 300cm. 9th X stands for the fitting number end connection type), which can be a number from 1 to 29, or 51 to 72 with the prefix: Nut and suffix: #, (if different end connection types are used two numbers will be provided Size 1/2” 3/8” (only used for stainless steel outer material) Size M15*1 M16*1 ( use brass material only, use size 13mm and 14mm only) Limits: 1. Size 1/2”can use all fitting number except #51 2. Size 1/2” 3/8” can use #13 and #30, but they are only used for stainless steel outer material. 3. #30 is used for stainless steel outer material and surface treatment of stainless steel natural color Size M15*1 only use #51, M15*1,M16*1 use size 13mm and 14mm only 4. ABS is only used in fitting size of 1/2’ 5. Only 14mm diameter is used nipple materials of stainless steel,POM and Nylon;other diameter only used brass material 6. EPDM,TPE tube only use with stainless steel and brass out side Model code example: IW-17SCB1/2”1/2”SPEX150 Nut 4# & 16#. This gives a 17mm hose with stainless steel interlocked outer, chrome surface finish, brass fittings, ½” end connections at each end, stainless steel nipples, PEX hose inner, 150cm length, end connections type Nut number 4 and 16.

Approval Holder:
Innowin International Co., LTD
Company Name
Innowin International Co., LTD
Address
No.377 Sec 3 Chang Tsao Road
Country
Taiwan

View All Listings by this Company

Print This Approval


#240988004

Range of stainless steel inter-locked shower hoses incorporating PVC linings in various finishes. Maximum operating temperature 65°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240988004
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
Open outlet use only
Size:
See model
Marking:
PPI, WRAS & year of manufacture (yyyy) on ferrule
Installation Requirements:
R001 R040
Expiry date:
30/09/2029
Model:
SHS(D)(C)-A-B-L-F (SHS(08/10)(P/B/S)–Connection A - Connection B– Length - different finish) SHS – The name of our Stainless Steel Shower Tube D(08/10) – 08=DN8 or 10=DN10 C(P/B/S) – P=Plastics Core Only DN8, B=Brass Core or S=Stainless Steel Core A-B – Connection A and Connection B (from 01 to 10) 01 = F1/2 knurled nut, 02 = F1/2 hex nut , 03 = F1/2 Conical Connection Shell knurled nut, 04 = F1/2 Conical Connection Housing with O-ring nut, 05 = F1/2 Conical Connection Shell without O-ring nut, 06 = F1/2 Conical Connection, 07 = T connection, 08 = M15×1 connection, 09 = M22×1connection(L=20-30)and 10=F1/2 cone-shaped connection anti winding (Connections 01, 02, 04, 05, 06, 07, 08, 09 & 10 applicable for DN8 hoses and Connection 01, 02, 03 & 06 applicable for DN10 hoses) L (XXX) Length (15cm to 200cm): 015=15cm 200=200cm F (XXX) different finish (Chrome Finish No suffix), Chrome = No suffix, Brushed brass = BGP, PVD Gold = PVD, Brushed Nickel = BN1, Gun Metal = GMG and Electrolytic Polished = EP1 For example: "SHS08B-01-04-150 would be DN8, Brass Core,F1/2 x F1/2 Conical Connection Housing with O-ring nut , 150cm long, Chrome Finish" and "SHS10S-01-05-150-PVD would be DN10,Stainless Steel Core,F1/2 xF1/2 Conical Connection Shell without O-ring nut, 150cm long, PVD Gold Finish."
Product Images

Approval Holder:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company
Manufacturer:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company

Print This Approval


#241002025

Range of elastomeric shower hoses with EPDM lining and ‘O’-rings. The product incorporates a flow restrictor. Maximum operating temperature 60.0°C Open outlet use only

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
241002025
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1/2" BSP (F)
Marking:
Hansgrohe logo on flow control (models 28 249 xx0 & 28 248 xx0 AXOR logo on flow control (all other models)
Installation Requirements:
R001
Expiry date:
31/10/2029
Model:
AXOR 28 127 xx0 28 128 xx0 30 246 018 Hansgrohe 28 249 xx0 28 248 xx0 Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Country
Germany
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 80 of 108

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.