A screwdriver operated spherical ball valve with brass body, chromium plated brass ball and EPDM O-ring. Maximum working pressure 5.5 bar. Maximum operating temperature 85oC.
Range of spherical valves incorporating a chrome plated brass body & brass ball. Maximum operating pressure 10 bar. Maximum operating temperature 65 °C.
Albion SLP series of normally open and normally closed solenoid valves with brass bodies. Maximum working pressures SLP**EE* models 12.0 bar, SLP**EE*H models 8.0 bar. Maximum operating temperature 70°C.
Range of Instantor lever action ball valves with brass bodies, chromium plated brass balls and PTFE seats. Maximum working pressure 25 bar. Maximum operating temperature 85°C
Range of spherical valves with stainless steel bodies, PTFE seats and silicone O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of spherical valves with PVC-U or ABS bodies and ball (see models).. PVC-U models with a solvent weld pipe connection are for use with PVC-U pipe (manufactured to ISO 1452) and are supplied with a PVC-U solvent cement. ABS models with a solvent weld pipe connection are for use with ABS pipe (manufactured to ISO 15493) and are supplied with an ABS solvent cement. Maximum working pressure 16.0 Bar. Cold water use only.
Range of gate valves with ductile iron bodies (blue epoxy coated) with EPDM coated ductile iron wedge and non-rising stem operated via a hand wheel operating member. Maximum working pressure: 16 bar. Maximum operating temperature: 80°C
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of cold-water inlet control groups consisting of an in-line, manually adjustable pressure reducing valve and a pressure relief valve pre-set at either 6.0 or 8.0 bar, housed within DZR brass bodies. The products incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. The pressure reducing valves also have stainless-steel strainers. Maximum inlet pressure 16.0 bar. Cold water use only. CWIC351300 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 6.0 bar CWIC351301 – Outlet pressure range 1.0 to 2.1 bar. Pressure relief valve set at 8.0 bar. CWIC351303 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 8.0 bar CWIC351306 – Outlet pressure range 1.5 to 6.0 bar. Pressure relief valve set at 8.0 bar
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
'KOCETAL® K100BK & KOCETAL® K300BK'. 'KOCETAL® K500BK’ was added to the approval in June 2025. Black coloured, injection moulded POM materials. For use with water up to 23°C.
‘KOCETAL® WR301 (white coloured) & KOCETAL® WR301 BK (black coloured)’. Injection moulded POM materials. For use with water up to 23°C.
'CELCON F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘CELCON F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch CELCON MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'FORMOCON FM130'. White coloured, injection moulded POM material. For use with water up to 85°C.
'J1200 (RBSIC) & J1300 (SSIC)'. Grey coloured, compression moulded and sintered, Silicon carbide mechanical sealing rings. For use with water up to 85°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOROGUARD 20 RED & GREY'. Factory applied, two-component epoxy coatings available in red and grey. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS dated 'Jan 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 74 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
