Range of press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with Multitubo multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Range of Talbot pushfit fittings with polyprolylene or acetal bodies and EPDM o-rings for use with MDPE PE80 pipe (BS EN 12201). For use above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pipe repair clamps incorporating EPDM double seals. The products are intended for use with stainless steel pipe manufactured to EN1124. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of urinal flushing mechanisms with a solenoid valve controlling the flow with EPDM rubber diaphragm. The valves are controlled via an infra-red sensor. The product also incorporates a servicing valve, DC pipe interrupter and flow regulator. Maximum working pressure - 6 Bar. Maximum operating temperature - 23 °C.
Range of packaged plate heat exchangers comprising of stainless steel plates with EPDM gaskets. The products are supplied with twin primary circulation pumps, a secondary circulation pump, 3 port control valve and a control panel with full Mod BUS BMS connectivity. Maximum working pressure - Primary and Secondary circuits 10.0 bar. Maximum operating temperature 85°C.
Range of integrated water circuits with plastic bodies and EPDM ‘O’ rings and gaskets. The assemblies incorporate flow switches, plate heat exchangers and plastic flow regulators. The primary circuit incorporates a 3.0 bar rated pressure relief valve. Maximum working pressures: 2.5 bar primary circuit, 10.0 bar secondary circuit. Maximum operating temperature 85°C.
Range of water meters with blue epoxy coated ductile iron body, incorporating an EPDM diaphragm, NBR ‘O’ rings, stainless steel strainer and a polypropylene rotor. The products incorporate a second bypass meter assembly and a check valve cartridge (however, the complete product has not been fully tested for and is not intended to provide backflow protection). Maximum working pressure 16.0 Bar. Cold water use only.
Range of ultrasonic water meters with blue epoxy coated cast iron bodies, EPDM ‘O’-rings and plastic flow straighteners. Maximum working pressure 16.0 bar (DN50 to 200) or 10.0 bar (DN200 only)
Non-metallic materials and components comply with BS6920 at 50°C
‘Wesan WP’ range of water meters with black epoxy coated cast iron bodies, plastic impellers and EPDM ‘O’-rings and seal. Maximum working pressure 16.0 bar. Cold water use only.
‘Gladiator’ range of in-line water meters with polyamide bodies and EPDM rubber `O` rings. The meters incorporate a plastic strainer. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Range of rotating piston volumetric water meters with brass or nylon PA66 bodies, incorporating EPDM O-rings and plastic strainers at the inlets. Maximum working pressure 16.0bar.
Non-metallic materials and components comply with BS6920 at 50°C
CZ4000 range of in-line water meters with polyamide bodies and EPDM rubber `O` rings. The meters incorporate a plastic strainer. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Isolation valve, stainless-steel braided EPDM lined flexible hose assembly and a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). For use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Three hole, basic rough-in set with a brass body, incorporating EPDM O-ring seals. The product is supplied with a shower hose and a stainless steel braided, silicone lined flexible connecting hose. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of two stage horizontal water pumps with plastic bodies, stainless steel impellers and shaft, incorporating EPDM gaskets and seals. The products also incorporate a non-return valve (not suitable for backflow protection) and an shock arrestor expansion vessel. Maximum working pressure 1.8 bar. Cold water use only.
Horizontal 5 stage pump with stainless steel body, stainless steel impellers, EPDM and silicone ‘O’-rings. Maximum working pressure 6.2 Bar. BS6920 40°C.
Range of vertical multistage pumps with either stainless-steel bodies or cast-iron bodies with a black epoxy powder coating, stainless-steel impellers, shaft and outer sleeve, EPDM ‘O’-rings and a silicon carbide + EPDM shaft seal. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
‘SCALA1 TWIN’ range of booster pump sets, comprising of two pumps with plastic bodies, plastic impellers, EPDM and NBR ‘O’-rings and an accessory set consisting of a base plate, plastic manifold and four brass spherical valves. Each pump incorporates a non-return valve. Maximum working pressure 8.0 bar. Cold water use only.
Page 70 of 112
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
