Range of UV disinfection units incorporating 316L stainless steel bodies and quartz sleeves. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
'Cage Overmould 214867'. Black coloured, injection moulded ABS component. For use with water up to 70°C.
'ABS-001 (natural - appears off-white), ABS-002 (white), ABS-003 (grey), ABS-004 (blue), ABS-005 (green) & ABS-006 (pink)'. Injection moulded ABS (with Biomaster 612 added) materials. For use with water up to 70°C.
‘PAM-MORTAR.D2'. Grey coloured (once mixed), factory applied Blast Furnace Slag Cement Mortar and admixture. Mix cement, sand, water & admixture in a mass ratio of 1:1.25:0.38:0.0008. Apply as per manufacturer’s technical data sheet dated 18/03/2021 (3rd revision) and cure for 48 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342 Food Grade Epoxy Coating'. Factory applied, brown-red coloured epoxy coating. Apply as per manufacturer's 'Standard Operating Procedure & Guidelines' issue number '116/2021' dated 15th Feb 2021. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac Two-Pack Epoxy Blue – 746 & Jerlac Two-Pack Epoxy Red – 747'. Factory applied, blue or red coloured, two-component epoxy coatings. Mix resin and hardener in a 3:1 volume ratio and apply as per manufacturer's instructions. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'35000 Kanpoly Purco'. Factory applied, two-component, blue coloured, solvent-free polyurethane based coating. Mix and apply as per manufacturer's instructions '0141', 'revision 02' dated February 2022. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyurea FA 1044'. Factory applied, two-component, beige coloured polyurea coating. Mix parts A and B in a 1:1 volume ratio apply as per manufacturer's TDS '07/2015 Rev.00'. Cure for 96 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cementitious Coating 851 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '851 /031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nitocote CM210 '. Site applied, grey coloured, two-component cementitious coating comprising of Nitocote CM210 White (base coat) and Nitocote CM210 grey (top-coat). 'Nitocote CM210 White' (base coat) consists of Part A (white coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 4 hours@20°C. 'Nitocote CM210 grey' (top-coat) consists of Part A (grey coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 8 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NO MORE DAMP Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0420'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LATTYflon 4789'. Yellow coloured, braided fibre/PTFE gland packing. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Aropol M 105 TA WRAS’ (formerly known as ‘Aropol M 105 TA’) & ‘Enguard GE NTRL HH WRAS’ (formerly known as ‘Enguard GE NTRL HH'): Translucent straw coloured (glossy one side textured the other), polyester laminating resin manufactured by hand lay-up & gelcoat (brush applied), sheet material. ‘Aropol M 105 TAXR’ & ‘Enguard GE WHI S WRAS’ (formerly known as ‘Enguard GE WHI S’): White coloured (glossy) on one side, translucent straw coloured (textured on the other), polyester laminating resin manufactured by hand lay-up & gelcoat (spray applied), sheet material. Apply as per Ineos Composites method statement ‘Preparation of laminated products for freshwater applications (WRAS)’, ‘code R071, edition 2’ dated 19.1.22. Cure for 9 hours at 23°C with 2% of MEKP-50 catalyst, post-cure for 24 hours@50°C and wash part thoroughly in water before use. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ForTii® WX11-FC BK00001, ForTii® PA Xgea21 BK28048 & PA Xgea21 BK28048'. 'ForTii® WX12-FC BK00001' was added to the approval in August 2023. Black coloured, injection moulded Polyamide materials. For use with water up to 85°C.
'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Omnix DW 4050 BK 001'. Black coloured, injection moulded PA material (manufactured in Oudenaarde, BE and Changshu, China). For use with water up to 85°C.
Page 62 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
