‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘TECHNYL ® SAFE A 219WFC V50 BK’. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
'TCM CPRO'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 02.03.2019. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet, (fixed), electronically controlled combination tap assemblies (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar. Maximum operating temperature 70.0°C.
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled, tap assemblies (chromium plated brass). The flow is controlled via solenoid valves, actuated by infra-red sensors. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, electronically operated tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve and actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose connection incorporates a stainless-steel strainer. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Page 62 of 89
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
