‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Polyglass VEF'. Factory applied, two-part, off-white coloured, vinyl ester coating. Mix parts A & B in a 98:2 mass ratio and apply as per manufacturer's instructions '2/23' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
‘ME2020’ injection moulded components. Silicone rubber ‘O’ rings and gaskets available in red, blue, white, black, light grey colours. Shore hardness between 30 - 70. Tested in-radii sizes between 0.5mm and 5mm. For use with water up to 85°C.
Range of brass press fittings for use with MLC PE-RT/AL/PE-RT pipe. Maximum operating pressure 10 bar. Maximum operating temperature 80°C
RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 16.0 bar @ 30°C and 10.0 bar @ 95°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20205.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20255.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20275.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20365.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No |
Range of stainless steel braided, EPDM lined flexible hose assemblies with DZR brass end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Page 7 of 8
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
